In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I'm seeing some odd flash behavior that doesn't make any sense to me. I have a nRF9160 communicating with AWS via MQTT. I'm subscribed to two topics, Print and Template. The...
Hi, my device is NRF51822 and i'm trying to enable Readback protection. In 'main.c' file i have added this code line:
const uint32_t UICR_RBPCONF __attribute__((used,at...
The example bootloader hex files within SDK 15.3 will load on the development board and seems to provide connection through nRF toolbox on a iphone 7 but will not load on...
Hi. I am using two application timers in my program, one timer ticks is fixed to 1000 means it will call its handler every second. The other timer ticks values I am changing...
Hi,
I use a mcu nRF52840 on a personal card for a project and we are stuck on interruptions: hardware pin and timer. I use the lib "nrfx" for future accounting purposes...
Using NRF_SDH_BLE_OBSERVER in a non-static context doesn't work because the registered variable, and therefore the handler context is lost. How can one register for ble events...
Dear,
I am using nrf9160 DK, we can download hex fiel for boardcontroller
nRF9160 DK board controller firmware
https://www.nordicsemi.com/Software-and-Tools/Development...
Based on the experimental_lpn example if have ported at application (light switch) to work as a low power node.
Everything work fine on the lpn node where i use the generic_onoff_client...
Hello,
I tried to update bootloader on the dongle via DFU, but It failed.
The dongle uses OpenBootloader, so it does not check signature for firmware packages. But the...
Hello,
I'm working on a project where we are doing the following:
Collecting sensor data and storing it in an external SPI flash
Retrieving that sensor data from the...
Hi,
When publishing a message with access_model_publish() the p_message->p_buffer must be remain valid until all retransmissions have completed for loopback message but...
Hello
I want to modify the tx powel level to 4 dbm using sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_adv_handle, 4); after Advertising_Init function.
I could...
Testing with the NRF52840 dongle and the Power Profiler Kit. I see a reading of ~5uA when sleeping without SAADC enabled.
I use this code to enable SAADC
My power...
Environment
- DK 0.8.2 in which SB44 is cut, and P1 and P2 are connected - firmware v1.0.0 - program : asset_tracker - SIM: iBasis
Before updating firmware, asset_tracker...
