I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
The Interface MCU Firmware link provided on the nRF52840-DK page is the same as the firmware for the nRF52-DK. Unfortunately, these boards use different nRF MCUs. Loading...
I'm using Windows 10 latest updates installed.
I can successfully build v0.4.0 but none of the other releases of lte_ble_gateway
The common error is as below, any help...
Hello,
In our project there is a problem that we encountered is happening when the Nordic BLE mesh advertising and connectable advertising for GATT connections are enabled...
Dear Nordic.
I am manufacturing PCBA product using nRF52810-QCAA
My customer request to me about environment and Minerals report
I need three type of documents as...
Hi all,
I am trying to "add" the DFU bootloader to my application and I have some questions regarding it:
my thought are:
add to DFU bootloader example code, part...
Hi, After compiling the at_command example form the new release v1.0.0 and updating the nRF connect tool to version 3.0.0 I get the something that looks like bad baud rate...
I am using J-Link debugger.
I am programming nrf51822. On the Jlink commander my desktop sees my J-Link Lite CortexM device.
When I try the run an example on keil5 I got...
Hi All,
I used app_uart_fifo.c and it worked however RX is not good so I switched to LIBUARTE.
The RX part is good with LIBUARTE however when TX traffic is high nrf_libuarte_async_tx...
Hi,
I am using the nrf52832 dk
i am using the uart code from the sdk.
how do i clear the rx_buf and tx_buf (buffers) and set the pointers to the beginning of the buffers...
I have read through the USBD section in the nRF52820 datasheet and I think I cannot do what I need, but wanted to confirm I am not missing something.
I would like to make...
Hi,Master:
See below:
BAT + = 3.88V
a).When I removed the MCU:BAT_ADC = 2.556V
b).When I soldered the MCU:BAT_ADC = 2.28V,Why is there a 270mv voltage drop?
In the...
Hi, nRF9160 modem firmware V1.0.0 avalable from nordicsemi.com.
"Please use nRF Connect Programmer to update modem firmware."
it means that open nrf connect and choose...
Hey there,
I am having a strange issue where once I connect to a PCA10031 device using the Bluetooth low energy app (v2.2.1) the entire screen turns white just after the...
I would like to setup a development environment for the Thingy. I see there is a User Guide geared towards demoing the example application, but there isn't a specific getting...
