Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I am beginner in nrf programming. I want to use NRF-ESB protocol to communicate between my Rx & Tx device with maximum battery saving techniques. For this i am using nRF5_SDK_12...
I enabled BLE buttonless unbonded secure dfu on custom nRF52382 based chip with s132 (SD version 6.0.0).
When buttonless service dfu control point characteristic is written...
I have established a connection with max30205, but I get only the first byte of temperature, how to read the second one? to get the tenths of a degree.
Now it works like...
Hi, I need to use a ble_hrs_t variable between two different files, I used the BLE_HRS_DEF() macro to instantiate the variable in a header file that I've included in both...
I am using the example from ble_app_att_mtu_throughput_pca10056_s140, changing the values for:
#define SEC_PARAM_BOND 1 /**< Perform bonding. */ #define SEC_PARAM_MITM...
Hi, I am following the Thread Border Router example provided in the info center. I have one Raspberry Pi 3 v1.2 connected to the internet via WiFi, one nrf52840-DK programmed...
Hello,
I am new to BLE and I'm following the solutions to the BLE characteristics tutorial for SDK 13.0.
I have successfully implemented my own external temperature...
Relationship between "LE Secure Connections (LESC)" and Bluetooth version
I am experimenting with the following contents.
・ "Central": iPhone 5s (Bluetooth v4.0) ・ "Peripheral...
I have a question about the sample project "ble_app_multirole_lesc(SDK V14.2.0)".
・ "Central": iPhone 5s (iOS V11.2.2) ・ "Peripheral": nRF52832(SDK V14.2.0, S132 V5.0.0...
Hello Nordic,
I hope you can help me. I'm using an NRF52840 DK development board.
I followed the instructions on this video to enable debug trace in Segger embedded studio...
Hi, I have a nRF9160 DK, and trying it out with my mac connected to the USB. However, I seem not to really connect to it? I've installed the nRF Connect app, and also the...
Dear All
We have implemented the the workaround because of the anomaly 195 for spim3 and it works as expected, but only once! After the following init
we can use spi...
Hi I am trying to init the serial on the nRF52840 Dongle but there are some defines missing in the boards/pca10069.h
I run this on the nRF52840 DK and it works fine.
NRF_SERIAL_DRV_UART_CONFIG_DEF...
