In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
We have implement a PPI for device match to trigger a GPIO toggle . but now we want to trigger a SW interrupt or a callback function .
my question is how to set PPI TASK...
Hi,
I merged UART exam ple from nrf5 sdk v14.2 with light switch client example from mesh sdk v1.0.1, i have 2 boards client board which is nrf52832 and server board which...
I'm developing an application using the NRF52832. Im using the ADC, and there may be times where the NRF52832 has 0V on its supply pin, but the voltage on the ADC pin is nonzero...
Dear Nordic Support,
does the BLE Uart example (SKD 14.2) inlcude any data link layer machnisms, for example error detection & correction, collision avoidance?
I implemented...
hi to all,
i am developing a ble device with nrf51822 and i encounter with a problem, in my program i have code like below :
in this point program work well, but when...
Hi
I'm facing a problem with light switch demo from mesh SDK v1.0.1, when running the light switch client, as shown in the rtt viewer below the configuration of the server...
My customer is modifying the code based on the example provided in the SDK 15.0.0 to suit their project:
Project file from the SDK under \ nRF5_SDK_15.0.0_a53641a\examples...
Hi,
I am making a project with the nRF52832.
In this project i must configurate another chip with SPI.
The timing must be very accurate. Now the problem is that the...
Hi Team,
I am using nRF52832 to implement smart watch product and it is now close to PP stage.
Currently our product testing engineer found that in a relative noisy environment...
HI. I used a translator.
I want to control the mouse and keyboard using HID with the nRF52840 PDK.
I found the HID example in SDK15 and compiled it
The Infocenter...
Hello,
The sd_softdevice_enable never returns, how can I investigate please ?
With my Jlink probe, it's look halted at address 0x000008CC.
Configuration:
SDK 15...
I''m trying to run a piece of PERIPHERAL example code running on a nrf51422 devboard
I'm using sdk 8.0 and the example's relative path is:
>nRF51_SDK_8.1.0_b6ed55f\examples...
Hi, We have a BMD300 nRF52832 acting as a BLE peripheral connecting to up to 8 phones acting as BLE central devices. We started noticing that we are getting BLE_GAP_EVT_DISCONNECTED...
Hi,
Just a small question. In the SDK 15 documentation for the Experimental: GATT Module documentation, could it be that the following sentence "The default value that the...
I can't work arround error 133 on Samsung S7. After several test I found that it's related to long advertising intervals. I've test it on nRF52 DK and nRF51DK. I've test it...
