Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I have a question about the wait_for_flash_ready routine in the nrf_nvmc.c file.
static inline void wait_for_flash_ready(void)
{
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
Hey,
I have my nrf 52 dk and nrf connect 1.1.1.
I have soft device v3 on my nrf 52.
I connect my board into my computer, NRF connect recognizes my board and gives me...
Hello,
4 of 5 times when i want to connect to my firmware using RTT the firmware crashes.
Commands that i use are:
terminal one: JLinkExe -if SWD -device nrf52 -speed...
Hello ,
I'm using nRF52810 with SDK 14.1 base on ble_app_uart example. where i am continously receiving the GPS data via UART. i am putting my GPS module in sleep mode...
Hello,
My setup is: ble_uart_app example, custom board with nrf51822, sdk 6, s110, nrf connect for pc.
I am advertising with my peripheral device. Whitelist is being...
Hello,
I am trying to merge the code of ble_app_buttonless_dfu with the code of ble_app_uart,
because I starts all implementation with the code of ble_app_uart at first...
Hello,
I am using SDK9.0 and testing the LED_Blinky project with IAR tool, Evaluation kit. The application is executing and leds are blinking but I am not able to set a...
Hi, and thanks ahead for the help. I am working on receiving ble packets without using the soft device. I am able to transmit an advertisement with raw radio and pick it up...
Hi,
I am trying to write and update a record in flash but not receiving event callbacks FDS_EVT_WRITE and FDS_EVT_UPDATE. I found that i need to add the following code...
Hi there
Is there any PCA10040 simple demo IAR project? Just like print out "hello world" from any debugging uart? Base on this I can add in more functions gradually. ...
I am using clock signal from external RTC chip to clock NRF52832 at 32768 Hz through XL1 leaving XL2 floating. I have verified the waveform by the oscilloscope and set SRC...
2.4g ble work in 2 mode(not same time) when reset.
when I init 2.4g clock
void esb_clocks_start( void )
{
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
NRF_CLOCK->TASKS_HFCLKSTART...
Hello everyone!
I have peripheral device with notify characteristic with 20 bytes length of value and connection time interval - 7.5 ms. So, I want to increase throughput...
