Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi,
I add the NUS in the ble_app_hids_mouse example which the sdk version is 14.0.
There are four services in the project: dis, bas, hids and nus.
When I connceted the...
hi all ,
I am looking out theory about SM layer in BLE . I read CoreV5.0 but I do not understand much about pairing , bonding , STK , LTK . Can you give me some document...
Can the link between two devices communicating with each other via NRF24L01+ be improved by using Tx messages with no ack (W_TX_PAYLOAD_NO_ACK) instead of messages with ack...
Specifically, sinking a Cree C503B green LED (Vf 3.2V at 20ma) from a GPIO configured for high drive, without a current limiting resistor, from VDD 3.6V?
Figure 23 “GPIO...
Hello All
We are using nordic thread sdk's sample simple coap client and server.We want to ON/OFF LED of coap client from coap server.
Can any one help how we can achieve...
In SDK13, the initialisation of the low frequency clock used to be done within sd_softdevice_enable . In the SDK14 version of nrf_dfu.c , the LF-clock is already initialized...
Hi, I want to use the AES-CCM of nRF52832. But it can not work with the softdivice. I have read the following question and answer.
https://devzone.nordicsemi.com/question...
Hello All,
I have a peripheral device where one service with 4 characteristics is implemented.
Out of these 4 in 3 services notify is enabled.
Now I want to subscribe...
I have a situation in which a central device (A) must be able to receive from a power constrained peripheral (B) with very low latency, but likely at long intervals.
To...
Dear Nordic,
I tried to download the new SDK nRF5-SDK-for-Thread from here:
www.nordicsemi.com/.../60504
However, when I clicked on it I only got the TTM 0.11.0.
...
Hi every one ,
I am using NRF51822. I download the code
from this link. github.com/.../nrf51-ble-tutorial-advertising
I able to flash the hex file & see board are...
hi~
i am working with nrf 51822 with custom board and softdevice s110.
i am using is7020-a20 temperature / humidity sensor via twi (i2c)
i tried 2 versions of twi example...
I followed this guide , I'v managed to run make files and flash them using the terminal, then when trying to build the project in Eclipse, I get this :
Make: no rule...
Hi,
I am following the "Bluetooth low energy Services, a beginner's tutorial", however, this tutorial is written for SDK V11.0.0 and I am using SDK14.1.0, softdevice 5...
