Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
i use RTC wakeup the sleep mode,project used the uart etc.
uart baudrate set to >=115200 sleep mode normally.but is baudrate set to <115200 sleep mode at 50ms+- periodic...
I am trying to use nRF connect's advertiser feature to simulate some sensor output for my testing. The sensors use BLE advertisements with scan response to send out data....
Hello community,
I am working in a central device with SDK 13 v. 4, PCA10400 (NRF52832) and SD 132 and one task is to receive 30 bytes from a sensors as a notifcation,...
Hi,
we are using are more or less unmodified version of the Secure DFU bootloader example. Especially all BLE/Softdevice configuration in "libraries/bootloader/ble_dfu...
As mentioned here , my poor little Thingy:52 doesn't work after upgrading to version 1.1.0 through the iOS app.
After getting my Thingy:52 i played arround with it for...
I try to add function for the peer manager initialization and set the security parameters. I did not understand keypress and lesc parameters exactly. Documentation says for...
HI,
I am using nRF51822 by Keil compiler. I found if it was programmed with boot loader
nrf51422_xxac_s130.hex
by nRFGo Studio.
Then if download user code by Keil...
Hello!
I fill in a dis struct with the fields manufact_name_str, fw_rev_str and sw_rev_str. Everything is dandy and works perfect.
Then I also fill in the field serial_num_str...
In product spec for nrf52832:
Neg30dBm 0xD8 -40 dBm Deprecated
Neg40dBm 0xD8 -40 dBm
Similar stuff in the SVD out of SDK 12.3
When I convert the svd to rust (using...
Hi,
I am using NRF51822 and sdk12.2. I am using Softdevice s130 with peripheral experiment_ble_blinky example. I have merge UART example in this and it is working fine. ...
Hello,
We've stumbled upon a weird behavior on iOS making the smartphone unable to reconnect to our wireless device after a DFU from SDK11 to SDK13 (nRF52832): the notification...
Hi!
I am getting a HardFault when I try to read a GATTs value inside a GPIOTE ISR handler.
I already tried setting the ISR priority to low as suggested in various posts...
Hi all,
I installed Nordic examples for Keil MDK, and I am able to compile the examples for the PCA10028 board, which is based on the nRF51422. But I intend to take the...
