Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello
I adapted the ble_app_uart with twi functionality.
Therefore I included the "app_twi.h" which includes the "nrf_drv_twi.h"
But as visible in the picture, the "nrf_drv_twi...
Hi,
I'm using nrf51822 with soft device s130 version 1.0 and I'm trying to flash hex file of size 108kb from both keil u vision/nrfgo studio.
Flashing is success but application...
Hi
I probably have done multiple or bad inicialization of flash memory in code
and my MiniBeacon ( www.alibaba.com/.../Nordic-bluetooth-nRF51822-logo-customizable-minibeacon_60408141084...
hi..I am using nRF52832 with sd 132 v4.0.2, I want to store data received over BLE in flash. So i wanted to know how much is the memory available to store data in following...
2017-03-01T12_28_45.220Z-log.txt Hi,
we experience an issue with the PC-based nRF Connect tool, details are as follows:
we use scan to discover BLE devices,
we...
Hello,
I'm actually working with a custom profile generated with Bluetooth Developer Studio. I'have some difficult to send characteristic with the template.
My setup...
I have a created a bootloader using the bootloader_secure example in SDK 12.1. Using my own public-private key pair I've created two zip files, signed with nrfutil, one with...
I'm modifying 'ble_app_uart' project with custom board.
And also test with Android app that Nordic released.
I'm wondering how to set this connection "bond".
Does Nordic...
Hello all,
I little confused with these two examples as mentioned in my question. Both examples are different and their use case is also different. Can somebody please...
Hi!
Faced such an anomaly. In 2-3% of cases when exchanging PTX device sees a transmission error (the ACK did not come) and device PRX is not see this error.
Is there...
These pins do not work when I connect to nRF51822 module directly..
Like this. I cennceted VDD, SWDIO, SWDCLK and GND to nRF51822 module.
And there are not jumpers to...
Is there any sample code in examples, because am a newbie to this great platform, my objective is to glow an led , when the motion is detected , and also when there is no...
Hi Sir,
I add NUS service into CSCS project base on nRF5_SDK_13 follow the steps below, there was no error occurred after build the project, but it didn't work. Please...
Hello,
I'm trying to set up I2C with an mCube cccelerometer, which has an I2C 7 digit ID of 0x6C and an 8 bit address (write) of 0xD8.
With the code below, I see on...
Hi.
I have a custom board, which I power up via AAA battery through a buck-boost converter. I wan't to measure battery level using on-chip ADC only on requests from master...
