I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I have two variants of the nrf9160 SIP one being the nRF9160 SICA B 0 A and the other being the nRF9160 SICA B 1 A.
When I use the AT%HWVERSION AT command on the B0...
Hi,
I want to write my own Multilink/UART example from scratch, because I'm too confused from all these examples.
What I need to get that code done? Or has anyone build...
I am trying to download the softdevice to the nRF52840 development kit using the nRFgo but:
1. On nFRgo I didn’t found the “Program softDevice tab”
2. Although the kit...
Hi
Migrating from NCS1.3.1 to NCS1.4.1, the Blinky sample stops working on my custom nrf5340 board. No compile error, but not running. I also have a nRF5340PDK. Works fine...
I want to use long range ble for advertising with nrf52833. I have a PCA10100 SDK board, and I'm running a program with type of BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hi!
So I've got one BLE Central and one BLE Peripheral that I should communicate. Ive based the Central code on nrf Connect SDK's "peripheral_gatt_dm" sample. First I...
Is there an existing implementation on how to do diversity (BLE) with dual antennas using nrf21450?
(could also be by using other antenna diversity switches / brands)
Hi! I'm trying to understand the possibility of doing a FW update to an empty NRF52810 chip via a host MCU running Linux. We have this setup on a custom PCB, whereas the host...
Hello,
I have two quick questions about the nRF24L01+ chip that I wasn't able to find from reading its datasheet.
1. Is the chip pre-programmed by Nordic or does it need...
Hi,
What does the AT%XOPERID command do exactly? Does it just return the operator, or does it change settings too, such as bands, system mode, psm, edrx etc?
Kind regards...
nRF SDK: 16.0, Device: nRF52840, module: BTX480XE, softdevice: ANT_s340_nrf52840_6.1.1.hex
The setup:
BLE and ANT running on same device concurrently. The device is modified...
Hi,
I am new to OTA, wanted to explore OTA. Is there any available example code for OTA in the sdk 17.0 or mesh sdk and how to verify it. How to proceed with this?
Thanks...
Dear Community,
I have been testing eDRX on nRF9160. For that, I have modified nRF Connect SDK "udp" sample. I have set eDRX cycle to 20.48s. My program does the following...
Dear all,
I am trying to run the MSC example in order to learn how to develop an application with MSC capabilities in the future. I have already run the example in its default...
