An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am running a modified version of the light switch example, where I have modified the generic on off model to send byte arrays.
So I have been changing my models...
Environment:
nRF5 SDK version: 17
SoftDevice: S140
Tool: Segger Embedded Studio
Debugger: J-Link EDU Mini
Board: Arduino Nano 33 BLE (Using SWD pins with the J-Link...
SDK 15.2, nrf52840 SD 6.1
I'm having an issue where a reset with RESETREAS DOG 0x02 is not coming through the WDT handler before executing reset. I can force this reset...
Hi,
I have the following application in mind: I want to create a bluetooth mesh network, in which one node will broadcast sensor readings, some nodes will be used to hop...
running sdk version 16 on nrf52833 ,
1. on power on , start advertise - " nrf connect" connected successfully ,
2. disconnect from the "nrf connect" , start advertise...
Hi folks,
I'm trying to find a pcb prototype manufacturer which supports the via-in-pad requirements for the nRF52840 package (i.e. 0.15mm hole size with 0.1mm annular ring...
I'm using the nRF52832, and taking ADC measurements, with 14 bit resolution and with Oversampling disabled. The nRF52832 Product Specification mentions the saadc can be configured...
Hi,
I modified the ble_app_att_mtu_throughput example to scan and advertise simultaneously. I want to have two nRF52’s that can read each other’s advertisements and pull...
Hello,
I have a system composed of one central that needs to 1) briefly connect to many (100+) peripherals, 2) download a small amount of data from each, and then 3) disconnect...
Hello,
I am working with SDK 15.3.0 and the nRF 52832. I am working with the Segger IDE v4.16.
I attempted to load the scripting as instructed in the SDK documentation...
Hi, I had this working, I'm sure of it. Now though I get 100% duty on one channel and 0% on another. Something's not right. Pins are correct, my focus is CFG_PWM_OUTPUT_FRONT_NUM...
Best regards:
Once the data was received in PRX, Is there a way forward (or modify) to PTX the same data and deliver it together with ACK payload in the same transaction...
Hello, i would like to test usb_msc example on a custom board, and i have few questions:
- will this QSPI flash chip work with nRF52840 QSPI interface, and is it sufficient...
Hello,
I'm doing some clean up in my code and i wanted to use only nrfx library as it advised to do. Regarding the watchdog i have set in my app_config.g file (used by my...
Hi,
Right now i am working on mesh sdk 3.0.0 on segger embedded studio and board i am using nrf52832. In my application i am trying to implement the watchdog timer but it...
