Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello,
I am new to embedded programming and I would really appreciate any guidance.
I am using NRF52832 that will interface with I2C USB charger BQ24295 ( http://www.ti...
Hello, I am working on Bluetooth mesh application and i am using nRF52832/40 for the development purpose. I wants to create one independent library with its own data section...
I need to burst write the DMP library into the mpu6050 but not succeed.
The following is the function that I've been using to burst write.
I have researched on the...
Hi,
We developed our device with KEIL 5, SDK15.2 and SoftDevice 6.1.1. After we upgrade the SDK on our device from version 14 to 15, our IOS phone encountered the following...
Dears:
I'm testing the USB mass storage example: \examples\peripheral\usbd_msc with Nrf52840DK and SDK v15.3.0.
Now I have one question. When I plug in/out USB to PC or...
Hi
I am using the NRF52832 ,my code is based on the ble_app_hrs_freertos example sdk 15.0.0
I have one main task which usually run 64 time every second using the vTaskDelayUntil...
Hi I have a module that is used in a hand held instrument. It contains the nrf52832. It connects to phones for data communications. Is it possible to determine the strength...
Dear All,
I am trying to compile and run the ncs/zephyr/samples/drivers on the nrf9160_pca10090ns. For this reason, I have copy-pasted the file under the ncs/nrf/samples...
Sorry, I want to ask that if I can send Decimal(like accel x,gyro x) by the ble characteristic to the nrfConnect, when I send the information, it always becomes hexadecim...
Dear community members
I have end nodes with nrf52832 (Soft device s132) that can communicate to a central nrf52832 DK in Connection mode based on ble app uart and multiple...
hello, I'm develop use nRF52 SDK15.3 template to measure water press, and gyro value.
but in nrftoolbox app just show signed value, so i want to show signed value.
please...
Hello ,every one ,I found that the nrf Connect will disconnect it self after connecting to the device after 30 seconds, I'm using the sdk15.3.0 ble_app_template example,I...
NRF5_SDK_15.2.0
I am run my android code on android 9 and android 7. Unfortunately my android 9 is paired sometimes and not paired sometimes. especial after i tried to connect...
I am currently developing applications using nRFtoolbox. In case of ses, we are developing a template, but the application does not produce a negative value. In this case...
