I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am working with NRF 51DK. I am trying to flash a software on the target device which uses NRF51 microcontroller. I am using NrfGo studio. I am facing an error that, Unable...
Hi All,
I am newbie with nordic, and I need some help.
I am using nRF52832 with softdevice.
I need to generate a 128 kHz clock signal (PWM pulses with 128kHz frequency...
Hello, everyone!
I am a newbie developer about nrf51.
I need to advertise my BLE and save my power.
I have read the document that nrf51 has System-on (including some...
We have a couple of development units that are showing the above error in the nRF Toolbox app. Using the nRF Connect app, the DFU dialog just goes away and the screen reverts...
What is the difference between 'NRF_SDH_DISPATCH_MODEL_INTERRUPT', 'NRF_SDH_DISPATCH_MODEL_APPSH' and 'NRF_SDH_DISPATCH_MODEL_POLLING' in the 'NRF_SDH_DISPATCH_MODEL' related...
Dear All,
Currently I'm developing a BLE module that will be useful by its uart service and will use nrf51822. Nordic provided an example based on sdk 6.1 for low power...
Hello,
I want to read data from mesh network (from all the servers) to send it to a gateway. I saw in the documentation that Provisioner s can be a part of gateway devices...
Hi all,
I'm trying to enable Bluetooth 5 extended advertisement in nRF52840.
Currently, I'm using Nordic SDK v15.0.0 and S140 Softdevice v6.0.0.
In order to init the...
Dear Nordic Support Team,
I want to send the new PCB layout for manufacturer but I am not sure that
I can use any pairs of pin for DFU over serial or not.
I want to...
Hi all,
I have a question regarding the BLE mesh specification. When you are transmitting data using advertising frames, how does it check if the transmission medium is...
Hello everyone,
I am working on DFU bootloader application for android and iOS (using Qt C++).
For android everything works fine, but for iOS I have problems.
In order...
for the mass production what is the best solution in order to flash the nRF52?
for the mass production can I use DK PCA10040 ?
The DK PCA10040 can be used for dubbug on...
Hi I'm using Keil MDK 4.7 with nRF5 SDK V15, both of the 2 SDKs are installed at C:\, and the Keil4 Nordic License has been installed. When I tried to compile one of the example...
Hi all,
Is there any possibility to intimate any documentation errors(spell mistakes, content doubts, etc) to nordic documentation team?
Thanks,
Sridhar
