Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello.
I need to use LESC numeric comparison pairing.
It seems that the PIN is automatically and ramdomly generated after the connection occurs.
I would need to manage...
I am running a nrf52 with IOT sdk's Cloud CoAP example. I am wondering about the parameters that I would need to integrate this into a product. These include the stack size...
Hello,
I am using 52832 to test ble data throughput. When two devices are close to each other, the throughput can reach 80kB/s, but if the distance is about 4 meters, the...
The nRF51422 product specification says that you have to use a +-40 ppm crystal for BLE applications.
On DigiKey, there are 2 columns for 2520 crystals: frequency stability...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello, I downloaded the ble_mesh_v0.9.1-Alpha source code from nordic website, and tried to port it to my pca10056 devboard.
When doing so, I noticed that some function...
Hi All,
I would like to use FreeRTOS in my project. I try to play with the examples/ble_peripheral/ble_app_hrs_freertos project.
I have enabled logging with RTT. The...
Hi, when reading BLE Mesh specs, this paragraph caught my attention:
Messages may support a delay parameter that indicates a delay between receiving a message and
starting...
nRF5 SDK v13.0.0
Release Date: Week 11, 2017
Highlights:
Implemented a new license scheme for the SDK distribution. See the
documentation folder for details....
Hi,
I am using "nrf5 sdk v11.0" ble_peripheral "ble_ancs_c" example for nrf52_DK(PCA10040) .
When i connect to the my ios device then accepted pairing request then i am...
is it possible configure the QDEC to single phase, i am using one omnipolar hall effect sensor i am wondering if i can configure only phase A ande use it, is it possible ...
Hi, I wonder why my pwm uses so much power in WFI mode. It uses around 470uA and when I do not use pwm that current is around 1.8uA. I tried to disable pwm but without success...
if i am not wrong the connections i found is as i shown in the image..
the module doesn't show up in my ide tool (keil ) although my kit works fine but i need it for standalone...
Dear Nordic Team,
I am work DFU with ble_app_uart example , as per the info center document : infocenter.nordicsemi.com/index.jsp and also followed by the example for ble_app_hrs...
