In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello
i am using Nrf52840 with sdk 132 and version 12.2
i am using the Heart Rate example as template.now i am just testing.
Before making connection,i like to Advertise...
I have a sensor which has output in the range of 0-5V. I want to connect it to an nrf51822 GPIO pin and to be able to read the value via it's 10 bit ADC. Is there any guide...
hello, there my application is like that...
(1) calculate size of receive buffer. than read that size of data.
again new data comes, then again calculate that size of...
Issue: With my external antenna design, I get lower dbm than PCB antenna (nRF51DK) with same distance.
My external antenna design: -70dbm
nRF51DK: -40dbm
In this...
Today when I started power profiler kit, it suddenly started to show peak values like 80 mA. This has not happened before, but the values with the same hardware have been...
In the data sheet of the NRF51 and 52 there is mention that sensitivity of NRF51 is -96 dBm and NRF52 -98.
But I read some where that when RSSI is -90 then that signal...
We are working on a dynamic radio power change for a proprietary RF protocol, and we are missing some granularity on the NRF_RADIO->POWER levels.
Typically we would need...
I am wondering what is the logic and magic behind using sdk API's to advertise vendor specific 128-bit service UUIDs. In the "Nordic UART Service" example (nus, SDK12.2.0...
Hello all!
We are designing our first projects with NRF52832 and the DC-DC decoupling capacitor on DEC4 pin used in reference design is:
1uF 0603 X7R 16 Volts
Our...
Hi
Now I'm using sdkv12.2 and S132 on nRF52832. All the examples in the SDK put the device name in the advertising data packet. However, for our applicaiton, we need to...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_STATUS_CODE_LMP_RESPONSE_TIMEOUT??
please...
For a moment I was thinking that I made it with Segger, I was thinking that after 3 days with Eclipse with no success, I managed to use the blinky example and flash it (!...
Hi.
I'v spent the last full days trying to set this up, and I am exhausted. I really am. Never had this kind of feeling in my life.
People from all over this place where...
Hello, the nrfTooolbox app from Play Store runs on my LG K4 phone which has 5.1.1 Lolipop. If I load the Github project into my Android Studio and try to run it on the phone...
