Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
I'm building the ble_hrs_app for my pca10000, I've made a couple of changes (to change the LEDS which show) and I'm building it with CrossWorks .. which I thought I knew how...
Hello, I'm trying to get my nrf51822 project from SDK 5.0.0 running in the latest SDK 5.2.0. To minimize problems with KEIL I used the template project and copied my sources...
Hello,
I have a nRF51822 Evaluation Kit, and a working ble_app_uart demo software.
I would like use the Fujitsu MBH7BLZ02-109004 module . I can flash and verify the softdevice...
I am using the following code to manage a buffer to put through data to the ble stack. I think I saw a similar code on the nRFready Desktop 2 v1.0.4 examples:
/**@brief...
Are there any pin restrictions for connecting the PWM module to? That is, would I be able to output the a PWM signal (created by the internal PWM facility) through any P0...
Hello Gentlemen,
I'm developing an Android App that needs to connect to nRF. The nRF sensor does not have keyboard, display or buttom.
But we can have OOB which is a...
Hello!
I have two question from Heart Rate Application.
What BLE_L2CAP_MTU_DEF number presents?
I do not see event handlers for WAKEUP_BUTTON and BONDMNGR_DELETE_BUTTON...
Development Board can not be loaded by Keil 4.7.2
nRF51 by Nordic can not be identified by Keil automatically, how to configure the parameter for programming?
The Android API Kitkat documentation says the following about BluetoothSockect.connect()
"This method will block until a connection is made or the connection fails. If...
Hello Gentlemen,
I'm looking for sample code that shows how to enable security which prompts for a PIN number on the Android device when I want to connect to the nRF. ...
On the box for the nRF51822 there's one tiny sticker with nRF6815, Rev 2.2.0, 2014.15 and 10004490 written on it.
I can't find ohter information on the box.
Hi ,
i would like to know about
1)how to enable softdevice in nrf51288?
2) how to check softdevice is enabled or not?
can any one share information related to it...
nrf51_sdk_v5_2_0_39364\nrf51822\Board\pca10001\s110\experimental\ble_app_uart
runs ok when connected to Android 4.4 Nesus7 II
but will return error code 8 when connect...
