We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello, I am currently working with VEML6035 light sensor and so far i had a hard time working with its 16-bit registers.
The code that i wrote:
overlay file:
I can...
Hi,
It seems like my system is crushing before going to deep sleep,
I have noticed that if I remove a k_sleep of 500 ms, just before going to deep sleep the system does...
It's successful when I use west :
% west flash -d build
But it's failed when I use nrfjprog :
% nrfjprog --program merged.hex --reset
OR
% nrfjprog -f unknown...
Hi nordic:
I use two NRF52DKs and download MESH CHAT separately, hoping to achieve communication between the two NRF52DKs:
SOFT VER: NCS2.8
The specific process is as...
Now I have a verification work on the nrf52840 development board, which is to verify whether the terminal device will perform signature verification after receiving OTA firmware...
I just freshly (Nov 25, 2024) installed the nrfutil 'core' exe and the nrfutil device command.
I try to list my nrf devices (a nrf52840 dongle is connected and another nrf52840...
I have some of these boards which come already flashed with the AdaFruit CDC/DFU/UF2 bootloader , allowing them to be programmed without a dedicated programmer. I wanted to...
I have noticed that the project name used for sysbuild is the same as the folder name where my code is checked out. So if I have the application in a folder named "src" the...
Hi,
I had a problem while programming my custom nRF52832 board using nRF52840DK. I am using this connection that I found in the Nordic Devzone forum. I am trying to program...
I'm developing my project by nrf5 SDK in nrf52832.
Pairing and bonding used in my project and implemented by peer_manager.The pm_evt_handler() defined as follow:
Due...
Hello everyone,
I was looking at SPAKE2+ example (NCS v2.6.99) and trying to understand where the password used to derived the shared secret is set or used. Can anyone help...
Hello,
I'm trying to move my project based on the xiao_ble board from using SDK 2.6.2 with Adafruit_bootloader to SDK 2.9.0 with MCUBoot/sysbuild.
To keep things simple...
nRF5_SDK_17.1.0
PCA10059
For I want to provide up to 20 central connections, I have defined the objects like this( inherited from example code):
The conn_handle is...
I have built my own firmware for my nrf54l15 custom board and got a merged.hex file.
Now I want to flash this firmware(merged.hex) to my nrf54l15 custom board on another...
Hi,
I have updated and old old project to SDK 17.0.1 and using Segger Embedded Studio
But because I make a lot of use of pstorage in the project - I am not ready to convert...
