Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I have been struggling to get the DFU in our own application to work. When starting a DFU from the desktop nRF Connect 3.4.1 it reports an error:
According to the log...
Hi,
We are using nrf52840 development board and segger embedded studio. I am using thread concept here to run another function in parallel to my main function. i want to...
Device: nRF52840, nRF5 SDK16.0, Softdevice: S340 (ANT_s340_nrf52840_6.1.1)
Hello,
As next step to increase usability of our product and adding new features, we have...
I hope someone is able to answer a few question.
I read quite a lot but still some things are still confusing.
If we use e.g. the AMB2621 Module of Würth, is skipping...
Hi,
I am trying learn about IO/ events that can wake-up nRF52833 from lowest power mode.
What qualifies as event that can serve as wake-up source?
Is it possible to...
Dear sir,
Got error while uploading .zip in DfuTarg as "SD version failure". I'm using nRF52840 DK board. I have tried to create .zip by --sd -req 0xB6/0XAE/0xA9. zip get...
I'm curious what the modem does if, upon waking up to service the PSM interval, it fails to connect? Does it go back to "idle" and try again on the next PSM interval or does...
Guys, In a Mesh project, when setting up flash manager:
How do you get the right value of flash_manager_config_t.p_area ?
And where and how is it configured?
Thanks...
Hi ,
I wirte a python script to download FW to nRF52832 custom board, the FW is the merged file with softdevice（s132_nrf52_7.0.1_softdevice.hex）, bootload, bootload settings...
The version used is nrf5_SDK_for_Mesh_v5.0.0_src.
nrf5_SDK_for_Mesh_v5.0.0_src\examples\light_switch\server.
Question 1: I want to turn off mesh broadcasting first,...
Hi
data sheet of the nRF52840 states that the QSPI port pins should be initialized to "high drive".
I've experimented a little bit because I have problems with a Macronix...
I have connected a BM680 sensor on a BL654 (NRF52840) via I2C. I have connected the power to the BME680 on a switchable power rail. I need to power this rail with a GPIO pin...
I am trying to create a test case for in house validation and would like to know how to do so.
Here is what I want to do:
I want to create a boot loader that checks...
Hello,
In nRF5_SDK_17/examples/dfu/secure_bootloader/main.c, the main program starts off with protecting a couple of flash areas:
But how can, after this, an OTA update...
I don’t know what all the XML syntax is, or what program processes the flash_placement.xml file, or what form the output is in, so I don’t know if I have to do exactly what...
