We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi.
I'm trying to read data of MAX30102 using TWI, it has 8 bits of data in the FIFO_DATA register.
The library I'm using for data extraction and processing was written...
Hello,
I am using the nRF52 DK with Segger Embedded Studio and the SDK 14.2.0. I wanted to build the example 'esb_ptx_pca10040' with logging enabled. To achieve this, I...
Hi,
I'm using the S132 on the PCA10040 with the external XTAL disconnected (SB1 and SB2 cut)
In order to check to if the external is present I call nrf_sdh_enable_request...
I am working on my first BLE project for my employer and have been unable to connect over BLE to our custom board with the nRF52840 processor. To eliminate issues with my...
I received a nRF9160-DK and was looking at working with zephyr/boards/shields/x_nucleo_iks01a3 but my x_nucleo_iks01a3 shield will not plug into the nRF9160-DK (DK) it seems...
I have setup a small thread network (1 FTD Router, 1 Border Router, 2 MTD Dongles) using the Nordic provided RaspPi border router image.
I have been attempting to get Thread...
In my custome PCB design, I am using the CHIP antenna , the same used in nRF 9160 DK, that is P822601 from ethertroncis. Can this antenna work for GPS too? If not can you...
Hello,
I'm currently working on a custom DFU op-code that allows the MCU to send a "pause" op-code, similar to the op-codes found in the DFU protocol.
The steps I've taken...
Hi All
I’m making a few tests on a custom board equipped with a nRF51822-AA device trying to update the firmware with a newest one based on a more recent SDK
The original...
nRF5 SDK version 17.0.2
In usb_dfu_transport_init we have this:
If the nrf_drv_power driver was already initialized, this will return NRF_ERROR_MODULE_ALREADY_INITIALIZED...
The documentation for the sd_ble_gatts_hvx() method states:
This function checks for the relevant Client Characteristic Configuration descriptor value to verify that the...
Using NCS v1.4.99-dev1.
I have no problem using the PWM with a nRF5340PDK but when i tried it on a nRF5340DK, my program was not working correctly.
I have made a simple...
