Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
My platform is SDK16 with softdevice, MCU nRF52840. I used 2 pin to generate PWM at 125KHz for Manchester coding. I want them are at different pin polarity. For example, if...
Hi all,
I am working with the nRF52 dev kit and the ecg sensor MAX30003. Using MBED to develop firmware.
I am using this library and the example code from maxim ( https...
Hello,
I need to develop an application for nRF51822 that uses SoftDevice 110 v8.0.0 using SDK 12.3 and extend it to use buttonless DFU for the legacy DFU bootloader of...
Hi, support team
I need to realize two-wire uarte receiver(with low power), in the scenario there is no data come from TX in most time, so after receiving the data I need...
SDK: 15.3.0
BOARD: custom nRF52840 pre-product
Hi, I want to implement usb dfu trigger library.
but, faced with a problem.
My project are started from usb cli...
cli_agent_router and multi_sensor example with nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 nrf52840
problem: The coordinator restarts occasionally, and the zed cannot rejoin until...
Hello,
I am trying to configure the SAADC for the NRF52810. I read that I have to enable it via the sdk_config.h. Here I find an entry for:
NRFX_SAADC_ENABLED - nrfx_saadc...
I have two related questions about nRF52 (nrf52832) which I have not been able to pinpoint from the documentation.
Can the 32MHz crystal connection be replaced by...
Hi. I’ve developed a custom device based on nRF9160 and now have a problem of fixing GPS signal. With the same antenna and same conditions sometimes it takes up to 10 minutes...
I've set up a timer which is firing the interrupt correctly. I then set up a second compare and linked it to the PPI to fire the ADC. The idea is to do these a few times per...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
Greetings!
I am using nRF52832 with SDK 16.0.0 and mesh sdk 4.0.0.
Application: light switch client with LPN features added
In one of application, I have to use...
i already done the nrf52840 dongle that already work as beacon when i have tried in nrf beacon apps. i want the same application but now it is transmitting to server/website...