Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
The Nordic Uart service for peripheral devices has a function ble_nus_init() which takes a callback function in a struct.. Later on this callback function may be called with...
I am doing the project using nrf blinky.
My phone cannot find the nrf52840 . Before this it is ok, but now it cannot discover it . I notice that LED05 is blinking very fast...
Hi guys ,
I am trying to connect thermistor with the ADC pins of nRF.
I use the steinhart formula to calculate the temperature in degree celcius. I used a voltage divider...
I have a development environment using Zephyr; setup and working from the documentation I found for the nRF Connect SDK. I am using SES and am able to debug the provided examples...
I am writing a Windows program to control an nRF52840 using pc-ble-driver, v4.1.1, with NRF_SD_BLE_API=6
I need to do all of the following:
1. Scan
2. Create multiple...
Hey guys (and merry Christmas),
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I try to receive data...
Hi,
I try to modify ble_app_uart so i can get a feed back from the boar if send something I use switch case for my use case, I'm working with eclipse
here what I do...
I have been working with the thingy91 source code from ncs, I can compile and load the sample app successfully. However I did notice that when I compile the code it does not...
I tried out DFU functionality initially using nRF52840-PreviewDK and UART transport
When downloading an app via DFU, It takes about 6 seconds from the time I start nrfutil...
Hi,
I am trying to make my own border router for Thread mesh network using nrf52840 and BG96. I have ordered pre-certified third party modules. Now How can I interface it...
I can't seem to find a data sheet on the PMIC used on the Thingy91.
The data sheet shows a ADP536x and discussions call out a ADP5360.
I searched the ADI website and did...
Hi all,
I am trying to test the OpenThread protocol by using CLI example.
Path of example is nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31\examples\thread\cli\ftd\usb...
Hi,
We use the nRF51 (nRF51822) on our products with the S130 SDK 2.0.1. In order to update the BLE application that we developed, we use the bootloader (secure bootloader...
Hello,
we are would like to drive 3 shift registers simultaneously using QSPI interface. We have look through QSPI examples but it looks like all examples are build around...
