Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
So I am using the Mesh SDK in version 4.0.0 and 2 nrf52DK boards with some custom software running on the boards, but derived from the light switch examples. The boards work...
We have some prototype boards that work fine when programmed via the debug out on the nRF52 dev kit, but have problems when programmed with this JLink . Programming with both...
Hi Team,
We are using the NRF52832 Board for our development purpose.We need the last RESET condition reason/source and need to store as log in memory for further debugging...
Hello,
I am looking for some tips to speed up a DFU transfer.
I have 2 BLE, I implemented a DFU master in the first one using SDK11.
Transfer duration is about 3mn30s...
Hi, I am trying to do firmware upgrade of nRF91 over BLE using nRF52 on the nRF91-DK or Thingy91 board. They both have nRF91 and nRF52840 chips on them which are connected...
I am currently working on a Heart rate sensor(max30102). I have connected the sensor to my nrf52 DK as follows: GND -> GND VDD -> VIN SCL -> P0.27 SDA -> P0.26 INT -> P0.17...
Hi everyone,
I have lately had some problems with my application which has different characteristics enabled, such as nus, battery service, dfu etc...
The problem I am...
Hi team,
I have 2 Thingy:91s, 1 is maybe new, not sure if I have used it before and 2 has been used before and reprogrammed over SWD many times before.
I wanted to test...
Hello,
I am working on my nordic board to make an https request to download some data that is about 4200 bytes. It is failing because of the BSD_IP_MAX_MESSAGE_SIZE=4096...
SDK 15.1 API 6.1 and i use SES
I removed previous as i was trying ot use fstorage. I switched to fds calls and it seems to work better.
However, does the fds calls take...
Hi,
I'm trying to configure the watchdog timer for my application but I am running into some "weird" things.
Is it correct that the reload value cannot be set once the...
Hello，I am using SDk14.1.How can I use NRF52832 connect to a specified host?I already know the MAC address of the host but have never connected to it。Can NRF52832 initiate...
Infocenter "Download offiline documentation" link is broken (see attached images). This occurs when using either IE or Chrome.
Please advise how to download SDK API.
Hi, Unfortunately, I'm stuck on this issue with running SDK-mesh example on Dongle. 1) I did: - took the project: nrf5_SDK_for_Mesh_v4.0.0_src\examples\light_switch\client...
I saw in this reply that the number of friendships a friend node can handle was limited by available RAM on the friend node. I set MESH_FRIEND_FRIENDSHIP_COUNT to 50 and after...
