to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
I am trying to update the firmware on the nRF9160 using the Programmer application on Mac. The Programmer does not seems to be able to connect (the switch is set to nR91 on...
Hello,
i’m using NRF52832 with SoftDevice S132 and Sdk 15.3 to develop a NUS peripheral and central. The system is tested as follows:
I have two NUS peripherals , a NUS...
Hello, I have questions about esim card.
1. Hardware footprint about esim chip.
I don't know which esim chip I will use.
So is there a common standard footprint?
If...
Hello,
I've a board with usb port
I can insert on USB the Raytac MDBT50Q-RX containing the nrf52840 and:
- my microcontroller can recognize it as CDC ACM USB serial...
Hi, I'm Developing Custom Board with nRF52832.
When I execute my custom code (by referring to ble_app_template example), an error occured.
First, my hardware spec below...
Hello, i am using the ble_app_beacon example on the nRF52840 DK with s140 and i want to send the service UUID for Device Information. I inserted the code from the ble_app_template...
i'm trying to get samples/drivers/CAN working with the nrf52
apparantly you need to enable CAN explicitly in menuconfig, which is already confusing because prj.conf has...
Hello. I met trouble, presented in the name of the thread. I use example for PCA10400e board. So, what I've changed to accelerate reproducing of this error. I change logger...
I have a question about the current consumption of GPIO and GPIOTE.
I want to use port in input configuration. Therefore, the following settings are made ("P_WUP_BLE"...
I have following problem:
I am using a multilink NUS Central. With one peripheral connection everything works fine. But when make a second connection I sometimes get an...
HI
We are developing a 2d-3d mouse .
We are trying to implement OTA-DFU into our custom board .
We first tried it on development kit and its working fine too . I can...
Hello all,
Environment:
Rpi with Raspbian Stretch (Release 9.8)
Kernel 4.14.8-v7+
Architecture armv7l
I have followed the below links to build BLE 6LoWPAN environment...
After compiling the SDK 15.2 ble_app_hrs_freertos_pca_10056_s14 example in Segger Embedded Studio there are a number of repeated warnings:
"configTICK_SOURCE" redefined...
Hi,
i've got the TWI scanner example flashed onto the NRF51 dk board, using the default "Arduino" pins of P0.07 and P0.30 as SDA/SCL.
I've added two lines to the example...
I have a small collection of i2c devices on the bus that can be jumpered in (sda/scl disconnected). I am currently using SDK v10 and Keil v4.
I wrote this code to namely...
