to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
I am trying to change the mac address of my device every time I advertise a packet. I have a callback on_ble_radio_active_evt where I update the address like this:
...
(I'm developing a firmware on nRF52832, but had actually stareted on nRF51822 and observed the same issue, SDK 12, pending migration to SDK 15)
When my app starts, I output...
Hi all,
I am investigating different protocols to support a network of very low-power Devices and Hosts. The Devices are mostly static (i.e. they don't move around very...
Dear developers,
I am developing a scheme where the nRF51 (central role) connects to iOS device (peripheral roles). The nRF51 connects, performs the discovery procedure and...
Hi,
I developed an application on the nRF51 Dongle (PCA10031) and am now trying to port it to this module. It is a nRF51822 AA device (256K Flash, 16K RAM), and it is Rev...
Hello everyone, I'm currently working on a project and I'm encountering issues.
The project involves with a BLE and a smartphone. The goal is to send Data from an application...
Hi
I have successfully(?) altered my application from using BLE_GAP_PHY_1MBPS to BLE_GAP_PHY_CODED. But how can I test it?
Prior to the modifications I tested the application...
Hello.
I'm trying to add encryption to the secure DFU bootloader. I'm using SDK v15. I know this topic has been discussed on this forum before. In particular I have found...
On NRF52840 DK, I don't have a softdevice installed. I want to do DFU with s140 softdevice only update. But it gives the following error:
raise NordicSemiException('Extended...
Hi,
I got a problem that doing the DFU through buttonless example, but successfully upgrade only in bootloader.
I used OPPO R9s (Android 6) with my personal cell phone...
which pin to use for TWI method communication, in board type 10040 nfr52832 model Taiyo Yuden EKSHJN
in file 10040 I have this definition of pins: what should i change...
Hello:
I have been at this problem for days now and not getting anywhere to a solution. My app is using a static passkey for encryption and does timeout after 30 seconds...
Hi,
I'm experimenting with incorporating " ATT_MTU Throughput" Example into our project.
I'm using nRF52832 as the peripheral and a SDK52 as the central.
The central...
Hi Everyone
I am trying to achieve the following objective
I want to upload the hex file of my application code which blinks leds after 1 second without using th SWD interface...
Hi,
I have my application working on NRF SDK11 on NRF52832 with softdevice 2.0. I am porting the application to SDK 14 and SD 5.0. I am facing APP_UART_COMMUNICATION_ERROR...
