I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I have a question on the supervision timeout: suppose that the slave latency is set to be 0, the CI is set to be 500ms, and the supervision timeout is set to be 4s。Once there...
Hi - I am following this tutorial and getting this error.
This exact question was asked; however, I do have the mkdir file in the C:\Program Files (x86)\GNU ARM Eclipse...
Hello,
This is less a question and more of a survey. We've recently completed development on a project using the nRF51822 but have run into an odd power problem. We built...
hello,
i am using the nrf52840 preview devkit and am currently trying to find a solution for timestamping / for a time-base. the idea was to use the RTC for that since...
i know that it's not up to you guys to tell me this but maybe you can give me a hint: right now i'm using the bluetooth developer studio together with the nordic plugin for...
Hi there.
I recently migrated from SDK 13 to SDK 14.0.0 and followed the migration guide in detail. I've found that when I try to advertise, ble_advertising_start() will...
According to the nRF52810 datasheet,the reference circuitry with DC/DC regulator setup connet the pin DCC and the pin DEC4. Then how much is the voltage output of the pin...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi
I am trying BLE multirole application ble_app_multirole_lesc from the SDK 13.0.0.
I am using nRf52832 DK along with GCC toolchain.
For debugging I am using Segger...
In the mesh network, the sender uses trickle algorithm to control the repeat sending process, and at last the sender will send the message forever in a max interval at a handle...
Hi Nordic Team!
After developing our firmware on the nRF52 HDK, we designed our custom board, and we're starting to write our custom board configuration file.
The main...
Hi,
we've developed a custom board with nrf51 and use bonding and white listing.
Everything works fine when connecting and bonding iOS phones with this devices but with...
HEllo,
I was wondering whether or not is advisable to use the same handler to handle transmission/reception of data over SPI0 and SPI1 interfaces.
I have two sensors...
Hello
I am using a custom board, based on nRF52832 CIAAB0. I have also S132 installed, and I am using SDK 13.1.0. TWI pins are P0.16 - SCL & P0.18 - SDA. The code is based...
