Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi,
I'm trying to implement a device including a PWM counter and a high resolution timer working with softdevice stack 110. Per the examples I got from this site, I'm using...
Hello! I'm trying to use s130 as peripheral.
I flashed nrf51822 with s130 stack. Opened peripheral example and build it with .ld file for s130.
After it I flashed this project...
we have a 2 chip soln. nrf for Ble, Atmel for main application.
config data is located in the Atmel part. Config data also has BT Device name, ADDR, Adv Params etc.
I...
I am thinking to use IoT SoftDevice in a project, but I read that
" This SoftDevice is a technology prototype only. Therefore, it should never be used in production ." This...
Hi there,
I'm trying to program an external nrf51 board (Xuntong 5518) through the nrf51-DK Debug out connector. So far I have no success and I'm wondering if I have the...
What exactly are the "glitch" issues with the PWM master library ? I see there have been some recent updates, but no clear indication as to what issues remain or have been...
Hi,
How to upload and debug application program to the beacon with S110_nRF51822_7.1.0 and bootloader (DFU) using J-LINK? The standard procedure takes into account OTA...
Hello,
I want to detect the advertising data of more then one Beacon with the SDK51 and read the TX_Power for a location-application.
I´m inexperienced in stuff like...
will gazell device fall-back immediately to out-of-sync state upon reaching the max tx attempts even if the sync counter is still less than the set sync lifetime?
thank...
I got a nRF51822 based module and I loaded a slightly modified application based on "ble_app_beacon" example in nRF51 SDK via SWD interface using J-Link. The code has been...
Hello,
I have an application in which a BLE peripheral device will be essentially permanently paired with a client. The client will need to connect infrequently with the...
Hi,
I am trying DFU example on nordic evaluation kit using example on github:
github.com/.../DFU-Bootloader-for-nRF51-Evaluation-Kit
However, while compiling in keil...
SDK 7.2
S130 Alpha 0.9
I'm using the UICR customer register address 0x10001080 to stare a single 32 bit number. The code below is a bit of "brute force" to demonstrate...
Hi
I'm trying to make a new S110 BLE project for my nRF51 DK from "scratch" in Keil 5.14 (New uVision Project -> nRF51422_xxAC) , but every time i try to build the solution...
