Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
I have pca100000 v 1.0 and v 2.1.0, and the master control panel application with the latest version of 3.5.0. The firmware we have flashed on both the dongle is 0.9...
Hi,
How can i run the nRF utility application using my Nexus 4 smartphone? After installing the application it is showing that device is not supported.
Regards,
Bala...
Hi,
For power critical application, i know that ,we need to enable the peripherals whenever we need that.
After we need to disable by using ENABLE register.
My question...
i'm testing in my pcb. i designed a nrf24le1f board (the guidance of the datasheet). But i transmitted not far, about 2-10cm a long. I don't know i wrong in design pcb or...
I have the nRF Loader app installed on an iPad Mini. I have the dfu_dual_bank_ble firmware from SDK V5.0.0 and SoftDevice V6.0.0.1-beta loaded on my nRF51822.
The app is...
Hi all,
I am in the process of debugging the ANT broadcast_tx example program using Keil on nRF51422.
I have flashed the program on nRF51422.
After entering the debugging...
I have nRF51822-EK
I am not sure whats going on with it.
I can run LED blinky example nicely ( no surprise :D )
But when I try to run softdevice examples like heart...
I have used TI Code composer which is based on Eclipse, and they created a specific Target menu option which allows resets and other target specific items.
Is there a CDT...
Hi,
I use the UART to do the device firmware update and have used the dfu_dual_bank_hcl to compile.I use the nRFgo Studio V1.16
to program the s110_nrf51822_5.2.1_softdevice...
I've downloaded the latest SDK and soft device. I've been able to compile the ble_app_ancs project, run it on my dev board and even connect to my iPhone. Although I'm getting...
Hi everyone
I'm using the nrf51822 connect with stm32f103 through UART,it's current is >1.9mA,is it normal?
I have full reset to disable the debug interface,it can...
Hello developers,
I've got an nrf51822 EVA kit with on it the QFAACA chip. KEIL v5.0.5, J-link V4.78, nRFGo Studio V1.16 and nrfGo SDK (zip) V4.4.2. The Softdevice on the...
when I enter the system off mode then used a GPIO to wake up the IC, the "RESETREAS" register show "Reset due to wake-up from OFF mode when wakeup is triggered from the
DETECT...
Hi,
I have only nRF51822 DK without starter kit motherboard. how can I download softdevice(S110 Bluetooth low energy stack) to my nRF51822 chip in the Keil environment?
...
