Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi, I cannot compile because of the error below. Thank you in advance for any help.
I have updated the toolchain and sdk recently. Tried also with 2.6.1 and 2.7.0, the same...
I am porting the LoRa Basic Modem to the nRF52832 , using the nRF5 SDK and Segger Embedded Studio (SES) . In my application, I am using SoftDevice and implementing FOTA ....
Hi,
We recently updated our NRF Connect SDK from v2.2.0 to v2.7.0.
After porting to the SDK v2.7.0 we are not able to build the project with DFU enabled. We get below...
What is the best method to ensure the nRF9160 LTE functions on a PCB during assembly with minimal test equipment? Our thoughts were to search for available networks using...
We want use NRF5340 to do le audio application. We got the demo from your website, and find the audio demo, but the min sample rate is 32khz can be set, we want to use 8K...
I'm working with a client's existing product. It has an external MCU connected to nRF52832 via SPI.
The nRF application & SDK code are compiled inside the external MCU source...
I now want to use the 52833's board to burn the host program and then connect to other nordic slave devices. But now I put \nRF5_SDK_17.1.0\examples\ble_central\ble_app_uart_c...
Hi All,
1. The SDK used in VS code is version 2.6.1, and running the periphral_uart demo can print in rtt, but not in sid_end_ device
The official routine is used for...
Hi
First of all i am quite new to nRF SDK so if the answer to my question turns out to be trivial then I am sorry.
I am in the process of developing a Zigbee light switch...
I need to check if the Ethernet cable is connected or not, I am using the eth_click for ENC28J60. I see the driver does not allow me to see directly if the cable is connected...
Hello, How can I purchase a nRF9131 EK from Nordic Semi Sales? I was informed at the recent "Getting started with NR+ PHY" webinar that nRF9131 EK can only be purchased directly...
I would like to take Nordic's "TF-M secure peripheral partition" sample project, and modify it to take data received from the secure peripheral and send it wirelessly to another...
Hi,
I am working with the nRF5SDK , nRF Thread SDKs long time. Recently i have update segger embedded studio to V 6.30 . previously i have used v5.68
1.
for nRF 5 SDK...
I've installed and used the tools on other systems previously, no issues..
I have installed the tools on a new system, and can not get build configuration to run.
nRF...
Hello,
I'm using nRF5340 audio application with nRF Connect SDK v2.7.0 on nrf5340 Audio DK. I didn't change anything in the sample code.
I build by this cmd:python buildprog...
