We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi Nordicsemi engineers,
While testing a large-scale OpenThread network recently, I encountered an irregular pattern of device crashes. The network consists of 70 devices...
Hi,
I am working with NRF54L05 SoC using NRF Connect SDK V3.1.0 and NRF54L15DK for testing.
I am seeing an inconsistent MCUboot validation failure when flashing a firmware...
As the title, in the project "ncs\v3.2.1\nrf\samples\nfc\tnep_tag", how to runt into function tnep_svc_one_selected()?
I use the NFC tools, Send the hex data, want to select...
Hi, Nordic and all expects.
I am checking whether EN 300 328 can be used for testing 2.4G proprietary mode of nRF 52/53/54 series; EN 300 328 is a popular RF standard for...
I switched from the nRF-bm\v0.9.0 to nRF-bm\v1.0.0 SDK and now I am getting the following linker error message:
c:/ncs/toolchains/66cdf9b75e/opt/zephyr-sdk/arm-zephyr-eabi...
Hello,
I would like to ask what is the maximum number of simultaneous TCP connections that can be operated on nRF9151-DK while using LTE-M?
Alternatively, is it possible...
I am using an nrf54l10 with the NRFconnect SDK. I would be interested in a solution to go into a low power state and wake up again after a specific time (multiple hours to...
Hello, I am trying to develop a 1000 Hz wireless gaming mouse. The mouse has a NRF52832 onboard and the dongle has a NRF52820 on it. (Cannot switch to 52840) I do know about...
Hi,
I am using zephyr v4.3.0, and have compiled the "https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/boards/nordic/system_off" sample to
run it on a Adafruit...
Does Nordic provide an application like nrFConnect for Desktop that could be used with a nRF52840 USB Dongle for a ZigBee network survey? Use case: Scan environment for existing...
Hi,
I'm developing with nRF Connect SDK v2.9.0 in VS Code. I followed the exercise l1_e1 from the intermediate course. When I debug with breakpoints and the first breakpoint...
On the nRF52840 using ncs/zephyr v2.6.1, how can I explicitly configure the Coded PHY scheme (selecting either S=2 or S=8) for BLE Extended Advertising? Please provide the...
I tried to fully replicate the example from DevAcademy ( academy.nordicsemi.com/.../) for my project, and added a button and an LED in the overlay. However, once SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello,
We need to interface the nRF54L15 with a 3-wires SPI slave (which uses one single bidirectional pin for MOSI and MISO).
I see two options here:
1. Connect the...
