Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hi,
I am currently trying to work with pairing and bonding between the peripheral and Central device.
I am using two nrf52840 dk one as central and the other as peripheral...
Hi,
I cannot start HFXO on nRF52832. I'm using 32MHz crystal TSX-3225 32.0000MF20X-W0(from Mouser) wtih 12pF caps UMK105CG120JV-F(also from Mouser).
Checked with beeper...
Hi everyone,
I'm trying to set the USB polling rate with the nRF52840 and it seems like I'm stuck at 8 to 9 ms polling (~125 Hz). I'm using the Zephyr hid-mouse example...
I am using this code to create and start transmission, but I cannot find a way to set the MACID to the internal NRF_FICR->DEVICEADDR values
My method with iBeacon is not...
I am currently working w/ a project that utilizes TrustedZone and PSA Protected Storage to read/write to internal flash that's accessible only in the secure partition (I'm...
Situation : custom nrf5340/nrf7002 board (very close to production...). Main image is overflowing available internal flash (with a MCUboot 64kB partition).
Secondary slots...
nRF52832 & nRF Connect SDK 2.6.1
We would like to reserve some internal flash for user configuration data that would be written in production like
and read by FW but...
Hi,
I am working with nrf5340 with the Zephyr OS. I created a custom data section in a custom linker file.
.my_data_section : { PROVIDE(__my_data_section_start = .); KEEP...
Hello,
I spent a solid two hours debugging an interrupt pin that was not working, to discover that the problem appears when configuring a callback in another part of the...
I have been bringing up an application on nRF54L15-DK, and about 50% of the time it hardfaults on initialization. I tracked down the cause to a branch to address 0, caused...
I am currently using DWM3000 EVK with NRF58240DK for a UWB indoor localization system. I want to use the timer to setup a localization period for each tag node. I tried several...
I am currently working on direction finding using the nRF Connect SDK in VS Code. I am using an nRF52811 custom board, and my logs work properly. I wanted to include timestamps...
Hello. I'm trying to control led in gpio pin in addition to LED pin in npm1300. I don't think you need to use resistance in LED pins, Is it the same when using led in gpio...
I am using NRF Connect SDK v2.5.2. Sometimes, after I factory reset my Zigbee router device, it will immediately join a network with PAN ID 000000000000. I get this with my...
I'm trying to move my nrf9151 project over to sysbuild (SDK v2.9.1) but when I try to use a custom board definition, the code fails to start up.
So far I've tried debugging...
