At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I stupidly plugged a battery into a nPM1304EK port with the wrong polarity and now I repeatedly get the error "module_pmic: No response from PMIC.". I've tried resetting the...
Hello, I am using nrf52832 along with S132 soft device and SDK 17.1.0.
Is Encrypted Advertisement possible with the above configuration?
If so is there a good example...
Hi Support Team
We follow the guidance of the following link to program firmware to external SPI Flash of nRF54L15,but it failed.
https://docs.nordicsemi.com/bundle/nrfutil...
Hi Nordic,
Do you have any CapSense examples for nRF52 or nRF54 on nRF Connect SDK (Zephyr)? If none, any recommended external controllers/drivers and minimal DTS/Kconfig...
Hi Team, We’re using the nRF7002DK + nRF5340DK (cpuapp) with nRF Connect SDK v2.6.1, and we’ve run into an issue during the BLE-based firmware update process: 1. The image...
Hi Support Team
Can the nPM1304 support the features that the current on VOUT1/2 can be read real time and the magnitude of the current can be controlled? Many thanks.
Hi, we need add the cluster color control to the project light bulb.
After add the build config and build the project for the firs time it build successfull:
But...
Hi Support Team
Is the oversampling mode the highest accuracy mode for the SAADC of nRF54L15? The datasheet mentioned a formula to calculate the improved SNR. What is the...
Hi Team, I tried adding battery reporting to the Matter bulb demo based on the nRF54L15DK. The device was successfully added to the Apple Home app, but I’ve noticed that it...
Hi,
I'm trying to enable support for MT25QL01GBBB memory on nrF5340DK. Existing flash has been soldered-off, the one from Micron has been soldered-in with two pull-up resistors...
Hi, I was curious if the orientation of the devices matter for channel sounding using NRF54l15. I have noticed that channel sounding works best when the initiator and reflector...
Hi,
I am trying to get an nRF54L15DK working with an nRF7002EK using SPI (not QSPI) and I cannot get this working using the wifi-scan sample.
I am using nRF Connect SDK...
I'm attempting to migration from using MCUBOOT as a child image to sysbuild using SDK 2.8.0.
Everything boots fine when building using a child image, but when switching...
