Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I've inherited a project where the software was developed in IAR and I've rebuilt it in SES. I am having an issue configuring the memory for the soft device.
The chip is...
For a project under development I used two NRF24L01 for testing and they work very well.
Now I would like to know if: is it possible to use one NRF24L01 as TX and several...
Hi, I am working on ble_app_template. I am trying to save a value in the flash memory of nRF52840. I am using the following 2 functions to write/read in flash memory but getting...
Hi everyone
I am using app_uart_put() method for sending data via UART. The problem is that when I send each byte I get each byte back to its event handler in APP_UART_DATA_READY...
I have a Thingy:91 connected to a Garmin LIDAR Lite v4 (built on the nRF52840) via four GPIO cables. The code running on the Garmin reads one GPIO pin to signal a measurement...
Hello, I just want to clarify a secondary takeaway from my post:
https://devzone.nordicsemi.com/f/nordic-q-a/60714/best-approach-to-store-nonvolatile-data
I would like...
Hello.
I'm invesigating this on behalf of a customer.
I bought a thingy91 and wonder if it is possible to stream live video stream?
I would like to mont a camera to...
Hello everyone,
I have a Python script on my PC sending data through serial port COM5. I want to know if it would be possible to read the data sent from the PC on the nRF9160DK...
My target is porting my host MCU (STM32) to update my NRF52832 code through the serial.
I test it on SDK14.2.0 and PCA10040 , the secure_dfu_serial example is working ,...
Hello,
I experimented with some different capacitor tuning values at C1/C2; the external 32MHz clock initializes just fine for C1=C2=10pF, C1=C2=12pF (nominal), and C1...
hi ,
im try to add some consumer keys and system keys to the project:
nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard
and my code of hids_init...
Hello! I'm trying to reach zigbee on nRF52840, and I'm trying to get a zigbee communication from light_bulb. The hex file on the sdk goes in well, and I want to add additional...
I just learn nrf52840-Dk
I can download hex and build for example light_switch mesh to nrf52840.
But light_switch project have too many C files.
Which one C file or...
Hello !!
My hardware is based on IOT application. I'm using nRF52833 SOC as end node and powered it through CR2032 coin cell. In system ON phase ( sleep mode) it is consuming...
