We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I have already went through every step as per what the documentation has stated, but I could not be able to sniff any ZigBee packets using Wireshark. I only want to perform...
I am trying to develop a first eval / test program for the BMD-340-EVAL evaluation board using Keil. However, I don't seem to be able to download the required Keil pack. Other...
Hi,
I want to send multiple packets on a notify characteristic using ble_blanky app as baseline but only first 4 consecutive notifications are received on android side....
I would like to set the UUID below, so please tell me how to set it. 1)base UUID: 2)Service UUID： 3)Status Characteristics UUID： 4)Control Characteristics UUID： 5)Blood...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I set tx power in advertising as below.
sd_ble_gap_tx_power_set...
Hi,
We are developing a product that consists of a "central" and "peripheral" device. A small amount of data is periodically send from the central to peripheral device...
Hi. We are using nRF52832 and we have problem with UARTE. SoftDevice version - S132 5.0.0, SDK version - 14.2.0. Our application uses nRF and Mbed Serial to communicate with...
I have created my own custom project based on the template ble app, porting over the relevant includes and settings in order to start fresh. Despite my section placement file...
Hello,
I'm using a development board PCA10040 with sdk 16.0 I'm trying to organize a data streaming between two devices. Nrf52 board collect data (27 bytes with interval...
I bought dev board for evaluation purpose (currently run on ESP32)
chip: nrf52832 board: E104-BT5032A-TB ( http://www.ebyte.com/en/product-view-news.aspx?id=956) framework...
Hello Nordic! Im making a custom Nrf5232 QFAA, and for the antenna, I want to use only a grounded micro-coax connector and not a trace antenna, is this even possible? I've...
1. I want to use the following command line to compile the nrf9160 project, but the error.
2. Can you help me find the cause of this error?
3. Please provide me with...
Hello, I encounter a problem when I am trying to measure the current consumption of the nRF52840 on the nRF52840-DK. I have set the board in direct supply mode as described...
Hi,
I'm using a nrf52832 based beacon with some sensors attached. To retrive the current time I use the CTS client. Actually, I'm following the ble_app_cts_c example to...
