Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
More of a plea than a problem. When I migrate to a new version of the SDK I try to be very careful. So, I use sha256sum to check all similarly named files from one version...
Hi,
I am trying to read the SFDP (Serial Flash Discovery Parameter) register of a Micron NOR flash memory using nRF52840 QSPI peripheral. The read SFDP register op code...
Hello,
i work on nrf9160 dk
I would like to know if it is possible to use an AT firmware to be able to easily switch to LTE-M, NB-IOT, send sms, switch off the modem...
Hi.
I am using nRF52840 & SDK 15.0.0.
I set the advertising slow timeout to 14 min, But, the advertising stops at about 3 min.
The followings is summary of advertising...
Hi all,
I'm using nRF52 DK.
I'm developing a program based on 'ble_app_uart_c' example with custom UUID.
When I type command using UART, central device send signal to...
HI, I have following errors while building a project in segger embedded studio:
1. 'TIMER1_INSTANCE_INDEX' undeclared here (not in a function)
2. 'TIMER2_INSTANCE_INDEX...
Hi,
Trying to compile one of the examples provided in the nRFgo SDK 2.3.0.10040 I get an error in the linker (error L204) Invalid Keyword. It seems to refer to REMOVEUNUSED...
Hi, When installing the nRF Connect SDK by using GSA application on macOS 10.15.3, at step "Installing the toolchain" I get stucked to a verification failure for python3 dependencies...
Dear All,
I have a question abou basic of BLE technology.
I'm using nRF52832 for our project.
My question is about avoding packet collision.
Please confirm my understanding...
Hello, I'm trying to use the PDM in the nrf9160. I'm using SDK tag 1.2.n I added
#include <nrfx_pdm.h> at the top of my main.c file.
I put
CONFIG_NRFX_PDM=y
in the...
We seem to be seeing slowness in a bare metal implementation. We would like to confirm the nrf52832 CPU speed. How can this be confirmed from within the codebase and/or logger...
Hi All,
Does anyone know what the maximum altitude is available for the nRF9160 GPS?
I know some GPS devices stop working properly if above pre defined heights.
The...
I have a PCA10040 board and use the development soft of SEGGER Embedded Studio for ARM 4.50.
I ran the project \nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_beacon...
While I was working with my dev kit this morning, the board has suddenly stopped responding to commands.
When I attempt to connect via jlink using Segger Embedded Studio...
This is definitely a stupid question but the uart ble example is littered with the likes of " NRF_LOG_INFO("Connected");". Where is this printed and how can I view it? I can...
