We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
The nRF52840 product specification version 1.1 contains for the table 160, 162, 164, 166, 168 and 170 the very same content. I suspect, that the correct content can be taken...
Hi, Im new here and microcontroller programming... I curently waiting nrf52840 PDK so Im only quick read SDK and documentation... Before Im program only devices with .NET...
Hi, I cannot open my project using SDK v1.3.0 (nrf9160dk_nrf9160ns selected board) I installed the v1.3.0 using nRF Connect v3.4.1 - Toolchain Manager I already downloaded...
Dear Nordic: I have issue about connect handle. My product supports 1 peripheral and 3 central roles. 1. For this configration, i am not sure handle 0 is resverd for peripheral...
Dear all, I have a question about IV index and sequence number in mesh network. If i have 3 nodes success provisioned. I will only power on 2 active node ( node 1 and node...
Can't see why this is occurring. I've checked my custom board and the reflow of the chip under microscope. The doc indicates this pin isn't linked to a peripheral. Despite...
I am using Nordic board to drive an accelarator. There is already an exist project and it can run successfully. I want to combine this project to a new project and it has...
Can I use the nrf52810 internal temperature sensor to measure ambient temperature? I know it is designed for die temperature but I don't need to know the accurate temperature...
Hello,
From my understanding, I should integrate the LwM2M Carrier Library connection as the first step in the boot process and once I have received the LWM2M_CARRIER_EVENT_READY...
Hi Team,
If we send 20 bytes of data to AES-ECB 128 bit (CC310/ mbed TLS) Crypto engines for Encryption/Decryption due to bytes padding, how many bytes it will become...
With iOS and Android smartphones we are advertising some ble frames.
With our own code on the nrf 52840 we get around 2-4 advertisements each seconds on the nrf 52840 chip...
Hello,
I am trying to use the peer manager on a nRF52832 acting as a peripheral with both bonding and legacy pairing on SDK 16.0.0.
The application configured with bonding...
I am using version 4.1 of the Mesh SDK and version 16.0.0 of the nRF5 SDK on Windows. I was able to successfully generate the ninja build files using CMake. However, when...
Hi,
I'm interested in multiprocol examples and I'm trying to compile examples provided by the latest sdk for nrf52840 mcu.
IAR 8.x doesn't work I have this error "code...
