Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hello,
I am using NRF52832(WLCSP package) and nRF5_SDK_15.2.0 for the product.
I also use IAR Embedded workbench 8.32.1 as IDE.
Few hundreds devices are assembled...
Hi,
I'm trying to figure out how to ping a specific IP Address from the nRF9160 via AT Commands. I can't seem to figure out how to do a simple ping to an internet server...
Hello! Board nRF9160-DK. Compiled and uploaded the project asset_trecker (merged.hex). The LTE Link monitor shows a cyclic reboot. LEDs do not blink. where is my mistake
Sorry,I want to know whate is the different between BLE_UUID_TYPE_BLE and BLE_UUID_TYPE_VENDOR_BEGIN, the Device name will become N/A when I use BLE_UUID_TYPE_VENDOR_BEGI...
Hi,
I'm studying the example about the nrf_crypto for implementing asymmetric encrypt and decrypt function.
The suggestion on the Dev_Zone is to use the share key to symmetric...
Hi,
Is there a possibility that the order of the responses can be different with respect to the order of the requests?
We check for the success status of the APIs sd_ble_gattc_read...
These two options in nrf_mesh_config_app are arbitrary for me if I don't understand how they should be sized.
From the documentation of the MESH SDK 3.2.0:
ACCESS_FLASH_PAGE_COUNT...
My app runs the following code, that is supposed to init the SoftDevice:
nrf_clock_lf_cfg_t clock_lf_cfg = { .source = NRF_CLOCK_LF_SRC_XTAL, .xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_20_PPM...
Dear Nordic,
We have developed a product utilized the NFC readable/writable feature of NRF52832. We have tested it against some of the HTC, Sony, Samsung, and Google phones...
Hi,
I will add feature "installation codes".
I guess that security API do work.
At coordinator side, zb_secur_ic_add, zb_set_installcode_policy functions
At end device...
I am trying to implement nRF52 Light Switch Proxy Server in nRF52832 boards. Everything works fine on behalf of board and it prints the Device UUID as well. Although I can...
i'm using nRF mesh sdk v2.1.1 with 2 boards and 1 provisioner board. I have un-provisioned 1 board with the help of config_client_node_reset(). I want to know the procedure...
Hi,
In your Light switch example, there is a GPIOTE_IRQHandler() in simple_hal.c. Since I added the nrfx_gpiote module to the project, this is conflicting with the nrfx_gpiote_irq_handler...
Dear：
I used the nrf9160DK version to 0.8.2, updated the latest firmware mfwnrf9160100, using the NBIOT SIM card, and using the SDK version as nRF Connect SDK V1.0.0. After...
Hi there,
I'm developing applications with nRF52840, SoftDevice 6.1.1. Normally the scan timeout is in step of 10 ms. But whichever the value I set between seconds, e.g...
