I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi there,
I'm just starting out to interface a sensor over i2c. Not having any experience I dove right in and succeeded in issuing single write and read commands via nrfx_twim_tx...
Hi
We are designing a custom board using only nRF9160 as a tracking device. I am connecting Switch and LED to generate various events. Is is possible for me to program nRF9160...
Hi everyone!
We are currently trying to use the nrf9160 DK in order to test the LTE-M coverage & low-power capacity. We ran into some issues regarding the low-power measurement...
When I used "nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_uart_c " , it run ok . But my hareware is used PIN33 for RX, PIN32 for TX. So I changed pca10040.h ,please...
Hello. I wish you a good day.
I'm developing the Nordic NRF5_SDK.
I'm developing the Ble_Central and Peripheral.
If you know how to add the Uart to the Fle_Central and...
Hi,
I would like to request the HEX code for part#nRF52840-QIAA-R in order to load the bootloader program into the chip.
Can you please help to check and advise?
Thanks...
Hi
Im trying to figure out how to migrate my quite large older project from and softdevice s132 to using s140 (SDK14.1 )in order to experiment with long range.
Besides...
I was looking at the nRF52832 used for Bluetooth modules. And I was trying to understand the Analog to Digital converter in the nRF52832. I was wondering if anyone had or...
I'm trying to make the initial connection and flash/debug my adafruit NRF52840 express through a Jlink EDU to SWD on the NRF board. I am trying to flash to the board in the...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi,
We are trying to install the nRF toolchain/SDK/SES etc. so that we can compile (modify for NB-IOT) and evaluate the nRF91 asset tracker.
We have followed all the steps...
I am trying to use a button to put the nRF9160 to sleep and to wake it back up.
I configure my button as follows:
gpio_pin_configure(dev, PIN, GPIO_DIR_IN | GPIO_INT...
Based on mesh3.1 sdk15.2 Can I add DFU service to light switch server? Used to upgrade firmware via APP nrf Connect? I added a dfu service to the light switch server with...
Hello,
I wrote the code for HT1632 using SPI Protocol
while debugging when it comes to below function it will stop debugging
HT1632_5X21_init( LED_MAX_DISPLAY_X, LED_MAX_DISPLAY_Y...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
Currently with one device...
