Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hello,
my current problem is, that my application is not running when flashing it via BLE DFU using nrf52832 on BLE Nano V2 and nrfConnect. But the same code runs fine,...
Hello, I'm having trouble opening CMSIS Configuration Wizard from SEGGER Embedded Studio on Ubuntu Linux.
I followed this video over here: https://www.youtube.com/watch...
Goodday all,
I have a few nrf52840 dongles that is not being picked up by the usb anymore. I have been looking for ways to reload them back to "factory defaults" but cant...
I'm using the bootloader_secure_ble example, nRF52832, SDK14.0.0, S132 v5.0, IAR 7.80, nRF Connect v2.6.1, and an nRF51 Dongle connection to the host computer (Windows 10...
The documentation on the SAADC peripheral driver is unclear about how the samples are handled. When I read the docs I was under the impression that when providing a multiple...
Hi All,
We are using nRF52832 in our product. We are facing issue to establish bootloader in it. We used example codes for bootloader.
Below SDK example and procedure...
This questions seems to have been asked before in bits and bobs, but it's been hard to get a full concrete answer to this, which should be simple (in hindsight) I hope.
...
I’ve provided radiated immunity test for our devise based on the nRF52832.
The test has been provided by electromagnetic pulse with a power of 10V/m ,duration 1sec and the...
I am testing on my own board. The SDK is nRF5_SDK_12.3.0_d7731ad IDE is IAR Embedded for arm 8.30, windows version. Softdevice is S130. chip nRF51822_xxAC.
The firmware...
Hi,
I am in need of merging ble_uart and proximity program.
is there any code already there
I need to sens the data from nrf to mobile and i want to know that the nrf...
Hello everybody, I am trying to exercise the DFU for mesh following the DFU quick start guide (v2.0.1). To put you in context I have four nRF52840 devkits, three of them are...
hi..
i am using nf52832 ... segger 15.2version ... while i am start to execute the code .. i am getting the error at nrf_breakpoint_cond ... then i tried to set breakpoints...
Hi,
I am new to software development and had a query about software version control with the Keil IDE using git.
As a beginner, I simply copied an example project in the...
Hello,
I'm on nrf52DK PCA10040, SDK15.2
I'm sure it's quite basic, but I don't get it. I just need to write actually two uint32_t value in flash memory (so FLASH_DATA_LENGHT...
Hi,
I have got a nRF542840 dongle, and I have installed all the required programs (I got all from this website: https://www.nordicsemi.com/eng/Products/Getting-started-with...
