Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
1、I down load the sdk about thingy52(about nordic 52832)，it is keil 5
2、the pack 《nRF5x-MDK-Pack-5-Clause-NOD》is down load,and it is install ok
3、but after steps2，when...
I am using nordic_sdk_7 with s120 softdevice on PCA10001 board.
I got BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST event from peripheral. Sending conn parameter update request to...
1、I have down load the thingy FW 2.1.0 which has three projects
2、I BUILD the 《pca20020_s132》，It is ok
3、and press the down load button in the keil
4、It shows download...
I am having problems implementing Device Firmware Update in Android. The specs of my development environment is:
Samsung Galaxy S7 Edge.
Nordic DFU API v1.5.1
...
Hi all,
I'm sending data with ble_nus_string_send() in a loop as shown below. If it returns an error it retries until it gets NRF_SUCCESS. I'm getting an error code 0x0013...
The DFU example given in SDK v12 is for secure bootloader. Hence, they are asking for public and private key. How to generate the key? Or is there any other way of disabling...
How do you do
Using E: \ Nordic \ nRF5_SDK_12 2.0 \ examples \ ble_peripheral \ ble_app_uart ble_app_uart routines, join in routine PWM program, cell phone bluetooth connection...
I am trying to record the time on nRF52840 with s140 softdevice.
I used APP_TIMER to setup the TIMER and app_timer_cnt_get to get the count. And then uint32_t app_timer_cnt_diff_compute...
Hello,
We are using ble_app_uart example for both central and peripheral. We can succesfully send and receive data.
We deleted the is_UUID_present control. And then...
hello
i am working with simple ble mpu example it is working fine but when i am trying to connect nrf52 DK with my android phone over bluetooth it is showing
the device...
I have analysed the light switch client and server example apps where the light switch is also the privisioner.
They both start and initialise a bit differently although...
Hello,
I used translation software.
I used the function to enable DCDC mode
I used sd_power_dcdc_mode_set ().
I want to use the optimal mode for power supply voltage...
Hello,
i'm using an nRF52832 as a Bluetooth to UART bridge, similar to the APP UART example.
Another controller (Cortex M7) is connected to the UART. I'm using UARTE with...
Hi,
I'm using two sensors with the same device address through I2C.
each sensor is supposed in a specific period of time (not working together), each sensor has a different...
I am writing a mesh beacon application based on Mesh SDK v0.10's beacon and light switching examples.
A very kind Nordic employee has provided an example on how to combine...
