Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
hi all
nRF24L01+ ???
as the data sheet wrote the support life :These products are not designed for use in life support appliances
what is mean this sentence ???
does that...
When I try to make a custom service with the S110, how do I set the service and characteristics up to use a custom 128-bit UUID instead of a 16-bit one, based on the Bluetooth...
hi Guys pls HELPPPPP
I have developing active rfID tag using nrf24L01+ and ATtinny13A, the program code is done perfectly, firstly I start developing the tag with separate...
Issue is related to:
devzone.nordicsemi.com/.../
Now I use latest SD S130_1.0
So, I added to my service characteristic with notifications enabled. But during discovering...
Hello,
I have a development kit with the PCA10000 and I can comunicate with the PCA10004 for about 5/6 meters what is ok for my application but now I want to comunicate...
Recently I needed to add some functionality, so the software could monitor when there was a ble gatt read characteristic event.
In the addCharacteristic code I simply set...
Hi, We have used nRF51 DK for developing an application where we used USB to load/flash the program code. Now we are in Pre-production stage where we can use only the nRF51422...
Hi,
I would like to extend the HTS service with measurement interval setting support. Bluetooth SIG specifies the measurement interval characteristic, which is easy to...
I'm using the example ble_app_hrs along with the HRM part of the nRF Toolbox iOS app . It makes sense to handle this in on_ble_evt in main.c but am unclear how I can recover...
Hi Team,
I am testing UART on nRF51 DK kit.
I have flashed uart_pca10028 .
I have taken out jumpers from P0.9(TX), P0.11(RX) and GND and connected to PC com port.
...
I have the example app working nicely now, so I want to export the project to a zip or something, effectively copy it, and put it elsewhere in my filesystem and work with...
Hi,
I tried installing the kernel (raspbian-kernel-zip Raspbian kernel for Raspberry Pi 3.17.4 ) on a Raspberry Pi 2 (Model B 1 GB). I found out that the Pi doesn't boot...
I'm trying the multilink central example with s120 and SDK 7.2 (because of simple_uart).
However, my PCA10028 board gets stuck at this macro:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
My code is attached but essentially it is saying that SPI_MASTER_0 is not defined when I compile. I have the line:
#define SPI_MASTER_0_ENABLE /**< Enable SPI_MASTER_0...
