Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using nrf sniffer. I have used both nrf51422 and nrf52832. Here I am facing such kind of issue like. Once I am saving my report in wireshark and starting sniffing...
Dear all,
I'm using nRF52810, I want to achieve low power consumption(<200uA). I have disabled easyDMA. Right now I want to know how to turn on/off uart anytime we wish...
Hello,
I am working on a custom nRF52840 module based board, using SES v14.2.
How can I control what is printed on the debug terminal, or what has highest priority to...
I have a BLE device for which the local name contains and apostrophe. When I run nRF Connect on an Android phone and view the raw data for this device I find the apostrophe...
Hi all,
I have an nRF52 acting as Central, and it will act as beacon just when it, for example, reach a temperature above a certain point. After some time, e.g 10 calls...
Using SDK15.3.
Using the logging in deferred mode with RTT viewer.
Getting the errors below from the macro expansions but I can't identify what is missing.
Went through...
Hi,
I made a temperature logging device using nRF52832 (SDK 12.3.0). The temperature sensor is read over I2C every 5 minutes and data is sent over radio communication. There...
Hi,
I have setup the SW project to run run FreeRTOS with BLE stack initialized and nus service started without doing any further BLE use after init in runtime. Sometime...
Hello,
I am using an Adxl362 accelerometer on nrf9160 dk board.
I followed the tutorial a to add the overlay file and even configure the pins i want to use by flashing...
To the kind attention of Nordic support team,
It seems gazell is a very good candidate to be used in tipical working environments, where a bunch (<= 5 devices for example...
Hi,
I am new to Nordic. I bought an NRF52 DK and a Fanstel EV-BT832 development board. As you can see in the picture, both boards are connected to the computer via USB....
Hi,
I had some of your example projects which were being evaluated within Keil and SEGGER and now have an issue with Keil after updating to the PRO license.
I now get...
Hi,
For a peripheral reset, I was recommended to use the code below.
I was just wondering about what the middle line does. Is this a kind of delay to make the reset...
I am trying to start the mesh alongside GATT profiles. I am getting error NRF_ERROR_NO_MEM when calling sd_ble_gap_adv_set_configure in mesh_adv_data_set, which is called...
