Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Is it possible to transfer 258 bytes over the TWI interface of the nRF52832 in one transaction ? The manual says that RXD.MAXCNT is 8 bit wide only. I need to read 258 bytes...
Hello,
I need help with my project. I am adding fds library to the light sw example.
I did this steps:
1. Included necessary *.h files
2. Added fds.c to the project...
Hi, I'm using nRF52840,
I created my app, then i tryed to program with bootloader using nrfutil.
I used dfu bootloader and i created a zip.
So i could flash bootloader...
Hi, every developers,
I am testing the example of ble_app_hrs_c and ble_app_hrs using 2 nRF52840 (in SDK 15.3.0 VERSION).
My goal is that data communication with two DK...
SDK : Mesh 2.1.1
IDE : SES
I have a node.
After this node provisioned the mesh network,I change this node model publish address by local.
then I restart this node...
On the UART and I2C operations, are the input/output pins configured using CMOS or TTL logic levels? I am trying to design a test to test signal integrity and there are some...
Hello, I am a new bee in using nRF52840. I have looked into the given example in SDK called usbd_hid_composite ( infocenter.nordicsemi.com/index.jsp . It worked well in my...
Hello everyone,
I need ble_app_beacon 1 second advertising and 5 second deep sleep mode i don't know how to implement that please suggest example code for beacon.
DK:...
I need to use Static OOB method with PyACI and serial library
When I sent cmd.OobUse with OOBMethod.STATIC , I receive error message: 2019-07-25 17:08:26,191 - ERROR - COM11...
Hi, I am planning to buy nRF52810.
I saw that nRF52810 has 24kB RAM and I think it should been more cause of my information of RAM.
But I am not so knowledgeable about...
Hi, I'm now trying to combine the i2C(Gyroscope) and Gatt service using nrf52840 (sdk15.3), but I can't understand how to add the service to my device,like service name:Gyroscope...
Greetings !!
Are the SDKs for 5.1 available now ?
It's okay if they aren't.
Can you explain simply, what am I needed to do if I want to use the SOC?
Needs in terms...
Hi,
I'd like to add a Custom Advertisee Service contains the node mac address in my Bluetooth Mesh Application.
I'm usiing Mesh SDK 3.1.0 ande nRf5_SDK 15.2
How can...
