Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
Ipv6 UUID 0x1820 shall be present in the advertising process. Is it mandatory to put it in the ADV_IND message or can it be in the SCAN_RSP one ? ... the scanner, 6BR...
Currently, we are testing Bonding & Connect.
Please see the attached log below.
If Click 「Bond」 on Android App (nRF Connect), disconnection occurs after "PM_EVT_CONN_SEC_SUCCEEDED...
Hello,
I have the following question: when developing a software product, I developed my own service. It consists of one characteristic and several descriptors (valid range...
On our products, we assign a custom sequential mac address to each unit (we use this number in other places in our system). I believe this is an issue due to the bootloader...
Hello all,
We are using nRf52832 DK.
We are trying to run TCP Client example from IOT.we have even burned the s1xx_iot soft device.We are getting the the error "CMSIS...
Hi,everyone!
I need to configure an external interrupt so that when the interrupt is triggered, I can do something else
When I configure it in the following code...
Hi
Hi i am trying my application for sleep and wakeup without gpio. Actually my work is to put my device(battery powered) in sleep for 5 minutes and after that it should...
Hi,
Download "thingy" sdk and re-compiling it; add SDK 12.3.0 sdk_components to the build and it is showing just 1 error:
can't find ../../../libs/libmpllib_Keil_M4FP...
Context: in my application, I need to know rather precisely when the SAADC is taking a sample. So I did a test and discovered something interesting.
I'm triggering the SAADC...
Hi Support Team,
Is there any information about light sensitive spec of 52810 WLCSP package?
What we concerns are:
(1) Which light is sensitive for 52810 WLCSP?
...
Hello, I am trying to integrate buttonless DFU functionality to my project.
However, when I compile the project I get this error
The steps I took was to start with the...
Hi
Env: Linux, command line, arm-gcc, softdevice 7, sdk 6
I am having strange behavior when running BLE based program (in nrf51822 and it uses ECB encryption), and...
I'm trying to be a good camper and stick to published SDK interfaces, but I'm stuck on one point.
I want to use the PPI to toggle a GPIO pin AND clear the timer on a timer...
Hi All,
I've been noticing that when attempting to stream large amounts of data (let's say 20,000 notifications of 20 bytes) to the nrfConnect app on mobile (using a Pixel...
