Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hai
i am able to store one array in flash memmory of nrf51822. but i need to save more than one set of data into flash and retrieve it separately.
how can i save more...
Hello Everyone
Is there any example code which uses indication property. Application nAn-36 uses notification property and as far as i read and understood about indication...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
HI, I have actually couple of (connected) questions,
Can a phone (v4.2 bluetooth) connect to a nrf52840 board that uses 5v bluetooth?
How many (BLE) connections...
Hi !
I just got my new boards with the NRF52 CPU.
When i burn the firmware that worked on the PCA10040 evk it works but on my hardware it resets immidiatly.
On my...
Is there a UART bootloader available for nRF52840? Doesn't have to be secure.
Already searched in SDK 12.2 and 13 alpha, with no success.
Thanks for your help!
I installed the latest JFlash (6.12d) from Segger's site, and it updated the JLink firmware.
However when I try to program the hex files downloaded from www.nordicsemi...
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL does not set the .burst field in the nrf_saadc_channel_config_t structure.
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE...
The app_fifo support e.g. in SDK 12.1.0, appears to have a serious problem when the read_pos/write_pos values wrap. i.e. when the fifo has been used over a period of time...
I have BLE400 extended board for nrf5. It has cp2102 on board from Silicon Labs. I installed drivers for mac and can see NRF_LOG_INFO via terminal. It would be great to have...
i am using nrf52840 with sdk 13.0.0-1.alpha. I want to boot the application from bootloader but by
using UART as a transport layer.
Would you plz help me?
I found end of address of fstorage from macro of "#define FS_PAGE_END_ADDR (fs_flash_page_end_addr())". But I want to change the start address of fstorage. Which macro or...
I have multiple GPIOs that are configured to use GPIOTE in my application. When one of these GPIOs is in the active state I start timer. Once the timer expires I want to enter...
