We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
We tried to run the blinky example in the contiki source tree, and we had a strange behaviour. The example code is here , and the hardware is here .
The issue is...
Hi,
I'm using a RF module with nRF24L01+. Sometimes the RF stop working, the module keep replying status of no rx data (all pipes).
The device is embedded into a device...
Hello
I'm testing latest examples on 10040 (SDK12 S132). I want to get autoConnect working on Blinky example with nRF Connect app but I'm unable. Has anyone tried this...
HI all Nordic Developers,
Recently, I am using nRF51 DK as a beacon scanner connected to my laptop (Baudrate: 115200), it works fine to detect the beacon broadcast from...
HI,
I am using development board of BLE nRF52832 battery which you provide CR2032 is support for good battery backups
please give the reasons behind in it?
Hi all,
Is the "to-be-sniffed" advertisement packet allowed to have incorrect CRC, or perhaps a missing CRC? I.e. Is it possible for the sniffer to just display the raw...
Hello,
A problem occurs when i run the DFU over UART on my board.My bootloader project references to nRF51_SDK_9.0.0_2e23562\examples\dfu\bootloader\pca10028\dual_bank_serial_s110...
ANT experts,
I have been looking at the nrf52 implementation of the ANT timestamp (and timesync) features. One thing that is rather puzzling is the fact that the documentation...
Hi. I have two nrf51 dongles that communicate with each other. When I set the transmission power to -30 dB, the range is almost like 15cm, but whe I set it to -20 dB, it has...
nrfutil version 1.5.5
On Linux Mint (Ubuntu like)
in folder nRF5_SDK_12.1.0_0d23e2a/examples/dfu/bootloader_secure/pca10040/armgcc
make
nrfutil pkg generate -...
So I'm trying to upload the application over BLE.
Load the S110 w/ nRFgo Studio.
Load the DFU w/ Keil.
Build the ble_app_hrs example project in s110_with_dfu configuration...
Hello everyone,
I am currently using a nRF52832. I've been trying to use the low power mode with little success. I have been seeing a current draw of about 3.5mA. I would...
I am using an NRF52 dev board to develops a device that connects to an Android and IOS device.
I am unclear on where pairing comes into play with relation to connecting...
Hi in my project I am using nRF5_SDK_11.0.0-2.alpha SDK, s132_nrf52_2.0.0-7.alpha_softdevice. and nrf52 DK board(PC10040).
My issue is, when I run the ble_app_uart example...
