Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Has anyone else encountered a recent problem while compiling projects using mbed online compiler (error message goes "Struct "" has no field "NRFFW" "RF_UICR->NRFFW[0]" in...
I am trying to implement a OTA DFU in my project. The DFU Examples given create a bootloader file of it's own and starts transmitting in the nrf51422 dev kit(DFU_Targ, ble...
Hello,
Platform nRF52 with SDK 11 (S132)
I use nrf_drv_spi_init to register a Handler (used for screen and SD card so it can be long)
I have sometimes crashes when...
Hello Everyone,
I have deveoped my custom Board using(NRF51) which has four test pins VCC GND SWCLK,SWDIO. I would like to program the custom board. So could anyone tell...
I'm getting the following log messages when I try to initialize the BLE stack:
First from CHECK_RAM_START_ADDR, I get:
RAM START ADDR 0x20002080 should be adjusted to...
Hi,
I want to debug the blinky project on a nRF52 dk (PCA10040) using Eclipse. I strictly followed the instructions as described here: devzone.nordicsemi.com/.../
I...
Hi,
Is there any documentation regarding nRF OpenMesh( nRF51-ble-broadcast-mesh) Security ? Explaining the security of the communication between nodes in the Mesh network...
Hi all,
I'm working on mbed os and I cannot use the softdevice_ble_evt_handler_set and SOFTDEVICE_HANDLER_INIT . Every time I build it, I get:
undefined reference to ...
Hi ,
I am using S120 ble_app_multilink_central example. I have configured UART0 in interrupt mode. I send some command and expect some response. It work very well in starting...
Our product is based on nrf51422_CEAA chip with softdevice S110, SDK 8.0.0, dual bank ble bootloader DFU.
We have modified the dfu bootloader example from SDK 8.0.0 to...
I read a document, "Setting up production test using DTM", "nAN-034 Application Note v1.0".
And, Figure 3 shows how to setup test environment.
But, I cannot find which S...
DCDC_testing.zip
Hi,
I am in the process of reducing power consumption in micro esb mode. I use the following code, just for testing. The following code consumes 18mA unlike...
It is possible to load a new firmware in a NRF51822 PCBA using the Nordic Development Kit NRF51DK?
Do I need a special connector?
This is the beacon Module I pretend...
Hello,
I have a board with an RFDuino on it which uses a Nordic nRF51822 internally. We are seeing a few of them auto-brick when the input voltage dips too low.
My first...
