I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
If I want to do a project following.
The central that has NUS service can connect to at least two peripheral .
Two peripheral also have NUS service.
I can receive notification...
Hi Guys, my project requirement is i have to make sure that my nRF8001 should bond with only one peer device. So i intend do a whitelist one peer device address, whitelist...
I'm trying to use 4 pwm by hardware
and 2 pwm by ppi.
It works pefectly purely.
and if softdevice included.
I have to change nrf_ppi_ to sd_ppi_ api.
and got no demo...
hi. As I know, if I want to change my nRF8001 Device name, I have to check "Over the air" and "From application controller with pipe" boxes in nRFGO Studio. in this case,...
Hi,
I want to make sure that the nRF52832 can start working (turn on) with a 1.8V power supply. Therefore I went to check the default value of POFCON register, in which...
Hi,
I got the PWM example code working, but I need only 3 PWM pulses (14usec on time and 34 usec off time). How do I configure the PWM pins to output just 'n' cycles? thanks...
Hello,
I have downloaded the nrf52 sdk (version 0.9.2) and following the steps listed here: infocenter.nordicsemi.com/index.jsp , to run the blinky led example. However,...
hi, i'm looking for layout and schematic (altium ver.) of attatched nrf module (nrf 51822 BLE).
how ans where can i get this ????
actually i need the imformation...
Hi,
For each sdk version there is a release note of known bugs which is good :-)
I guess it lists the bugs known at the time of the release of the sdk.
Are these posts...
Hello,
I am developing in NRF51 with gazelle communication. I specify in project setting (in IRAM) to use full RAM of my nRF51, and use MicroLib. My last working application...
Hi,
I wonder if anyone knows any free C++ compilers for nRF52. I tried the mbed but it is not fully supported for nRF52.
The regular GNU GCC: arm-none-eabi-gcc works perfectly...
We are working on a project using the nrf52832 (SoftDevice s332 v0.9.1alpha, nRF5 SDK 11.0.0) in which we build a library as a hex file and and load it into a known flash...
Hi Guys,
I am using Bluez 5.39 on Ubuntu 14-04 acts a the peripheral by running "example-gatt-server" which creates 3 services and serveral characteristics within it. ...
In a project, I know the Bluetooth address from the machine, also know the phone's address. I want to let Bluetooth devices from the computer and mobile phone side of Bluetooth...
When I use the example of ble_app_uart(SDK : nRF5_SDK_11.0.0_89a8197) to measure data througput ,I find that i cannot get the complete packet of 20 bytes.
The operation is...
