Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi all,
We are running into a problem with our battery powered nRF52.
The nRF is continuously powered by one lithium cell. When the battery is very deeply discharged ...
Hello,
In our current design, our boards use P0.18 connected to an external watchdog to reset the nRF52840. We configure PSETRESET[0]/[1] to be 0x12 (Connected/enabled on...
Hi,
I am using Zephyr to do some action in a main loop and ksleep for 30 seconds. While in ksleep(), I can see that the consumption is 20ua. The board is a very small simple...
I have a Fanstel Evaluation board which can be programmed through 52 DK board, no problem there and i also have built a custom board using the BM833AF modules based nRF52811...
Hi,
I was wanting to know if this function has been changed since mesh SDK v2.2.1? It appears to not behave quite the same. When I call it, I think the mesh does not entirely...
I am currently working on sending some custom data using BLE nrf52.
I find the BPS format best suited for my application but I want to modify the systolic and diastolic...
I am adding dfu capabilities to my app on SDK12.3.
For that, I took the example on sdk12.3/examples/ble_peripheral/experimental_ble_app_buttonless_dfu and copied the relevant...
I am trying to modify the receiver an transmitter examples to change the default bandwidth on both the receiver and transmitter. I have looked through documentation without...
What is the communication distance of NRF52832 Bluetooth reference? Since nrF52832 is used for the first time, we are not sure about its performance. Is it possible to reach...
Dear Team,
I am try to customize the some of the parameter of HTS221 temperature and humidity sensor used in thingy52 board, However if I change any of the parameter then...
I am using the nrf connect desktop application on windows with a PCA10059, and have found the application to be buggy when receiving a flood of notifications, this works fine...
I've been logged in for about a week now, and still can't log out.
I left a posting about that almost a week ago with some "bumps" later on the "back stage" section, but...
Hi!
Can anyone tell me that isthere any app which logs data automatically into txt or csv file from nrf52???
I am getting data at nrf connect but every time i need to...
PCB : thickness 1 t(1mn), 1/2oz, 2 layer
The antenna was removed and the VNA was connected between L3 and C6.
The impedance was about 100 ohms.
The part value is shown...
We have a latest set of prototypes which use an NRF52840 on a Laird BL654 module.
On two of these protoypes the module is unresponsive. We are using a J-Link Lite module...
