We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hey,
I´m working on a project based on nRF52840, SDK 15.0.0 Softdevice s140 v6.0.0 running FreeRTOS.
I´m reading data from an external Flash via SPI and transmitt the...
Hi
I am running UBUNTU 32bit
Which "nRF Connect for Desktop" version does run on 32bit LINUX?
I have tried several with no success.
Thanks for any help ti get...
hello.
I want test dfu example.
so I was compile & download secure_bootloader example(nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader).
I just compiled and...
Hello everyone,
I want to know about Connection parameters updated means and why to use it as mentioned above and when did the next connection parameter is updated and...
In a current project we have a nRF52 Bluetooth application where the Central communicates directly with a Peripheral (also nRF52). The nRF5 SKD V14.0.0 or newer is used for...
Hello,
I have been following this case to create my own bootloader for nRF52810, but I'm using gcc/Segger Embedded Studio instead of Keil.
I have modified bootloader_secure_ble...
Hi.all:
I'm doing a project, it include freeRTOS+emwin(TFT screen SPI-->32Mhz)+BLE(central+peripheral)+FATFS+flash(qspi)+TF card(spi)+GPS(uart)+wifi(uart)+other IC(spi)...
I am working with a SmartThings Multipurpose Sensor connected to a nRF52840-DK running the ZigBee CLI as a coordinator. I am able to have the sensor join the network and I...
SDK11, NRF51822
if I use the fstorage_test at the applicaiton_init(void), then runs ok.
but on my product, I use a key to power the system, if I use the fstorage_test...
We are implementing DFU over serial to the nRF52832 from another microcontroller.
We are using SDKv15.30 and a slightly modified the serial bootloader from the DFU bootloader...
Hello, I am developing a big project with the nrf52832 + several peripheral devices and I want to integrate the notion of unit test to my project (in Segger embedded studio...
When trying to build my BLE Mesh app based on light_switch server example app from nrf5 SDK for Mesh with added functionalities (like detecting GPIO state changes and firing...
I'm attempting to create a DFU update using the the ble_app_uart example coupled with the BLE DFU bootloader. It's not unlike this case .
SDK = v16.0.0
nrfutil = v6.0...
Hello Nordic Team,
I have loaded the ble_app_uart example on my custom hardware. There is a button connected to P0.13. When that button is pressed I receive a NRF_BREAKPOINT_COND...
