Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
What is the limitation in terms of the number of bytes that can be sent over the UART to be sent over BLE on the usart ble example? I tried sending 32 bytes and it worked...
Greetings,
I am working with serial mesh (nrfSDk 15.2 for mesh 3.1 with softdevice s132_nrf52_6.1.0) .
1. I followed the serial example available and its working.
2...
Env: nrf52, sdk15, ubuntu, SES
Hi First steps on fstorage. As I just need to store and read an array of some bytes I have chosen fstorage
and I got this as output...
Hi,
I am working on DFU over Mesh for quite a bit now. I did run few tests but never run the DFU on a large network comprising of 100+ nodes. SO, I have questions about...
Hello
We are trying to finalize the layout we need for a nRF9160 module with gps capabilities.
I have downloaded the schematics and layout for the devkit V0.8.5.
what...
my code based on file "nRF5_SDK_14.0.0_3bcc1f7.zip".my hardware based on nrf52832QFAA.
my options set as:
project “bootloader_secure_ble”：
project “ ble_app_hrs ”with...
I changed the bootloader size by changing the flash start address (in the .icf file, from 0xf8000, to 0xf7000). I just want to check what other files/settings needs to be...
I need to use pin 8 and pin 20 as outputs on the nRF52 DK, to be transferred to a custom board built with the nRF52810. I'm using SDK v15.x.x.
I need to drive PWM output...
Im trying to detect power off. The signal power off looks like:
The time to get 0V equal 15seconds. GPIO EVENT and COMP do not see changes in the voltage level, they are...
Hi folks!
I'm working with a couple of nrf52832 on custom boards. I'm trying to implement a procedure for firmware updates. I've already played with the examples from the...
I have found many questions regarding passing bonding information from the application to the bootloader (e.g. https://devzone.nordicsemi.com/f/nordic-q-a/34497/dfu-with-bonds...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
I am using "twi_scanner" example code on Development kit. I connected HDC2010...
Errata for nRF52832 Rev 2 version 1.2, errata item 20, RTC: Register values are invalid, has a recommended workaround that i'd like to ensure i've implemented correctly -...
Hello,
I have a project that does what the title states, create a Mesh Network using the Nordic USB Dongles then provision a smartphone using GATT to access the Mesh network...
