At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I'm developing an application with SDK 15 that requires multiple concurrent links. One peripheral link and several central links.
I want the peripheral link to have...
I am new to nRF,
Unable to read data using flash data storage example.
When ever i try to read it
throughs error and processor enters into error handler and hangs there...
Default startup:
Using ble_multi_lesc as my default project
Log of original connection is in attached logLOTest.txt file
Currently only 1 nrfConnect is connected and...
hiii......
i am using nrf52832 interfacing with temperature sensor using temperature sensor example program..15.2v
i want to read the temperature ..... my temperature...
I have an application where I'd like to change the advertising content every time it is transmitted. Is there any callback from the SD after transmission of advertising data...
Hello. In my application I am using nRF5 SDK 15.2.0 9412b96. I am trying to communicate with two devices on two different SPIM instances. The first device is a DW1000 radio...
Dear Sir:
We observed that everytime we use OTA to update the firmware of the nRF52, the 6Byte address will change, just minus 1 compared with before, such as
FC:AE:3F...
I am using the software PWM library (SDK12.0) with the DRV8834 to drive a bipolar stepper motor. Although the motor is working in both directions with the code below, the...
Hi, I want to make sure that all application data are erased when we do a DFU, so that the newer application get a clean start without having to worry about data from older...
For nRF9160, is there an overview of the builtin CA certificates?
I have now deleted all certificates I added manually with:
int nrf_inbuilt_key_delete(nrf_sec_tag_t sec_tag...
We are using NRF52832 with SDK15.0 to develop a wearable device that collects data every 10 seconds. It works fine except that NRF52832 shuts down automatically 1 hour after...
Hi
My SPI Master wraps SPI comms using a couple of additional logic lines nReadFromSlave (Master Output) and nSlaveReady (Master Input).
It treats an SPI transaction as...
Hi, everybody. I have a Thread mesh network (wireless) running multiple nodes. I am using the CLI to send pings between the nodes and i analyze the mesh performance. My problem...
Hi there!
The documentation defines two possible return values for sd_rand_application_vector_get : NRF_SUCCESS and NRF_ERROR_SOC_RAND_NOT_ENOUGH_VALUES . I am wondering...
Hello,
I use ble_thread_dyn_mtd_scanner with BLE beacons but there is never any advertising received ?
If i check with my smartphone, they are detected.
Any idea please...